Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
For example, while setting the hardness (step 2), the beeper sounds #1 SELECT button UP button DOWN button _ s_ waw. qll41Ptal4_r _ 1141m, md laNJmlmd _ aad _ mq_q_l_ aymqmm J #2 SELECT button repeatedly when the display reaches 1 using the DOWN button, or the highest hardness setting using the UP button. 1. SET PRESENT TIME OF DAY: NOTE: If the words-PRESENT TIME do not show in the display, press the #1 SELECT button (FIG. 1) until they do, or see the notes above. • Press the {_)UP/DOWN _)buttons to set the present time. Press UP to move the display ahead; press DOWN to move the time backward. If the present time is between _,, m H:flO. noon and midnight, be sure PM ; • _wt ilu shows. ,e J If the present time is between ; midnight and noon, be sure AM shows. I0:%" NOTE: s s 4 Each press of the UP/DOWN z buttons changes the time by 1 minute. Holding the buttons in changes the time 32 minutes each second. SECTION 1 WATER SOFTENER START-UP 1C. PROGRAM THE TIMER 2. SET WATER HARDNESS NUMBER: • Press the #1 SELECT button once to display 15 (flashing) and HARDNESS. The grains per gallon (gpg) _,, ,,,, LP4_. hardness of your water sup-; ply is on your water analysis ; report. Be sure to enter water i test results on page 2, for --'-- future reference. NOTE: If your water supply contains iron, compensate for it by adding to the water hardness number. For example, assume your water is 15 gpg hard and contains 2ppm iron. Add 5 to the hardness number for each I ppm of iron. In this example, you wouhl use 25 for your hardness n umber. 15 9P9 hardness 2ppm ironx5 =10 +10 (times) 25 HARDNESS NUMBER • Press the _UP/DOWN _buttons to set your water hardness number in the display. The DOWN button moves the display to 1. The UP button moves the display to the highest setting (see maximum setting for your model in the specifications). NOTE: Each press of the UP/DOWN button changes the display by 1 between 1 and 25. Between 25 and the highest number, the display changes 5 at a time-25, 30, 35, etc. Holding the UP or DOWN button in changes the display twice each second. :3. SET RECHARGE (REGENERATION) TIME: • Press the # 1 SELECT button to display 2:00 AM (flashing) and RECHARGE TIME. At the 2:00 AM RECHARGE .....2:DI " =,.'4.-.-,, TIME setting, the softener begins regeneration (see pages 12 and 13) at 2:00 AM, ending no later than 4:00 AM. This is a f good time in most households because water is not being used (see AUTOMATIC BYPASS, page 14). If a different RECHARGE TIME setting would be better for your household, do the following. • Press the []UP/DOWN {_)buttons to set the desired RECHARGE starting hour. Be sure to observe the AM-PM as you did when setting the present time of day. NOTE: Each press of the UP/DOWN buttons changes the display 1 hour. Holding the buttons in changes the display twice each second. • Press the #1 SELECT button once again, to return the present time, and RECHARGE TONIGHT in the display. IF YOU NEED HELP PROGRAMMING THE TIMER, CALL TOLL FREE, NUMBER 1-800-426-9345. SEE PAGES I0 AND II FOR OTHER FACE PLATE TIMER FEATURES. SECTION 1 WATER SOFTENER START-UP 1D. SANITIZING THE WATER SOFTENER Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener will not infect or contaminate your water supply, and will not cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the softener. For this reason, sanitizing as follows is suggested (17when installing. 1. Lift the salt hole cover and use a pail or hose to fill the salt storage tank with at least 3 gallons of water. o Remove the brinewell cover (FIG. 3) and pour about 3/4 ounce of common 5.25% household bleach (Clorox, Linco, BoPeep, White Sail, Eagle, etc.) in the softener brine- well. o Press the ON/OFF-HOLD button and holdfor 3 seconds to start a recharge. This first recharge does several things. -It draws the bleach into and through the softener to sanitize it. -It fills the salt tank to the water level needed. -It gets all the air out of the resin tank. -It makes the resin bed (see page 11) ready for service. NOTES: This recharge takes about 2 hours. You can sanitize the softener with or without salt in the storage tank. ADD WATER Salt Hole Cover hose Brinewell Cover "emove and add about 3/4 oz. bleach) Brinewell Water, About 3 Gallo_.._ _'1:; Recommended by the Water Quality Association. On some water supplies, the water softener may need periodic disinfecting. SECTION 1 WATER SOFTENER START-UP 1E. FILL THE STORAGE TANK WITH SALT Brine (salt dissolved in water) is needed for each and every regeneration. The water for making brine is metered into the salt storage tank by the softener. However, you must keep the tank filled with salt. Fill the tank with NUGGET or PELLET water softener salt. DO NOT use rock salts, as they have dirt and sediments that will stop the softener from working. Before filling, be sure the brinewell cover is in plac...
Эта инструкция также подходит к моделям:Водоочистители - 625.34854 (1.36 mb)
Водоочистители - 625.34855 (1.36 mb)
Водоочистители - 625.34854 (1.36 mb)
Водоочистители - 625.34855 (1.36 mb)