Оценок - 2, средний балл: 4.5 ( )

Производитель: Sears Размер: 1.36 mb Название файла: Язык инструкции:

7) at a fast rate to flush iron minerals, dirt and sediments from the bed and to the drain. The bed lifts and expands for good cleaning. WATER FLOW THROUGH THE SOFTENER IN BACKWASH Hard Water iN Hard Water BYPASS Drain bed and expa •FAST RINSE: Backwash is followed by a fast flow of water down through the resin tank. The fast flow packs the resin bed and gets it ready for return to service (FIG. 8). After fast rinse, the softener returns to service. Hard water goes into the resin tank where the resin bed again takes out the hardness minerals. Soft water goes to the house soft water pipes. WATER FLOW THROUGH THE SOFTENER IN FAST RINSE Hard Water IN Soft Wafer OUT II!E_" Drain 13 SECTION 2 HOW YOUR WATER SOFTENER WORKS II 2B. SOFT WATER SERVICE AND REGENERATION AUTOMATIC BYPASS During the brining, brine rinse and backwash cycles of regeneration, HARD water goes through the softener valve and to the house pipes. If a faucet is opened, hard water is there for your needs. However, you should not use HOT watm, if possible, because the water heater will refill with hard water. The softener regenerates from 2:00 AM to about 4:00 AM, (you can set anytime), a time when not much water is used. If you get up early in the morning and you can hear the softener regenerating, change the time setting. Set the recharge time to 12:00 AM or 1:00 AM (page 7). Then regeneration will start and end that much earlier and your water heater will not refill with hard water if a hot faucet is opened. Two main parts of the softener's electronics are [] a WATER METER, and [] a COMPUTER. [] WATER METER -The water meter is in the softener valve outlet. As water flows through the meter, it sends electric pulses to the computer. The computer changes the pulses to a measure in gallons of water. [] COMPUTER -The computer is part of the circuit board. It is programmed to know the softener's capacity (how many grains of hard ness minerals it will take out of the water before a regeneration is needed). When starting the softener, page 7, you set it for the grains per gallon (gpg) hardness of the water. To find a regeneration pattern best for your needs, the computer uses: (1) water usage from the meter, (2) hardness setting, (3) softener capacity, and (4) time since the last regeneration. The computer always adjusts this pattern to your water using habits. It works toward providing you with soft water for the longest time and the most efficient salt usage. Softening capacity is used as hard water goes through the softener and hardness minerals are removed, capacity is used. When the computer determines that only enough capacity remains to provide soft water up to the next regeneration starting time (2:00 AM, or as otherwise set) it will schedule a regeneration. RECHARGE TONIGHT displays until the regeneration begins. When the regeneration begins, TONIGHT goes off and RECHARGE NOW flashes during the 2 hour regeneration. 14 SECTION 3 CARE OF YOUR SOFTENER II 3A. SALT. REFILLING STORAGE TANK/BREAKING A SALT BRIDGE WHEN TO REFILL WITH SALT: The Salt NOTE: Monitor System (see page 10) will turn on the You will have a loss in softening capacity and low salt light to warn you when to refill with salt. may get partly hard water if less than 10 inches Check for a low salt light a few weeks after you (salt monitor level 2) of salt is in the storage tank. install the softener, and every week after that. Always refill at about the #2 salt monitor level. At this level, the tank is about 1/3 full. Never let the softener use all the salt before refilling. Without salt, you will soon have hard water. PLEASE SEE PAGE 9 FOR SALT FILLING DIRECTIONS. BE SURE TO RESET THE SALT MONITOR, PAGE 10 SALT BRIDGE Sometimes, a hard crust or salt bridge forms in If the wrong kind of salt made the bridge, take it the salt storage tank. It is usually caused by high out. Then fill the tank with nugget or pellet salt humidity or the wrong kind of salt. When the salt only. bridges, water and an empty salt. Then space forms salt will not between dissolve the (melt) SALT BRIDGE in the water to make brine. Without brine, the resin bed does not regenerate and you will have hard water. V bPUd_tt:l iLnt°ak alt If the storage tank is full of salt, it is hard to tell if you have a salt bridge. Salt is loose on top, but the 1,,21__1 bridge is under it. The following is the best way to check for a salt bridge. Salt should be loose all the way to the bottom of Mark the tank. Hold a broom handle, or like tool, up to the softener as shown in FIG. 9. Make a pencil mark on the handle, 1-or 2-below the top height Broom Handle I-Salt of the rim. Then, carefully push it straight down into the salt. If a hard object is felt before the pencil mark gets to the top of the tank, it's most likely a salt bridge. Carefully push into the bridge in a few places to break it. Do not try to break the salt bridge by pounding on the outside of the salt tank. You may damage it. 15 SECTION 3 CARE OF YOUR SOFTENER 3B...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: