Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Attach camera using these (4) holes 1" 2" INSTALLING QUICK RELEASE BRACKETS JVC VN-C30U 2539 Mounting Plate: 1. Remove the mounting plate from the camera and place it onto the quick release bracket using the (3) metric 3M Phillips head screws provided with the kit. Then place the mounting plate back onto the JVC VN-C30U. 2. In the packet, there will be a number of 2 inch and . inch spacers. Take four of the . inch spacers and screw them onto the spacers that are on the base bracket (to make a 2. inch spacer). Place two 8/32 X s Philips head screws on the two and a half inch spacer in the dome. Be sure to place the screws so they line up with the two open screw slots on the quick release bracket. Place the JVC VN-C30U pan/tilt and quick release bracket in the housing, sliding the two open screw slots over the screws in the housing. Slide the bracket forward, and then tighten the captive screw on the bracket. Attach camera using these (3) holes ." 2" INSTALLING QUICK RELEASE BRACKETS PANASONIC BB-HCM381 / KX-HMC280 2539 Mounting Plate: Attach camera using this hole ." 1" 2" 1. Install the camera to the 2539 mounting plate using the . x 20, washer and lockwasher provided. 2. The Panasonic BB-HCM381 / KX-HMC280 requires 3." of spacing to properly position the camera within the housing. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. INSTALLING QUICK RELEASE BRACKETS PIXORD 261 / 262 2630 Mounting Plate: Attach camera using these (3) holes ." 1. Install the camera to the 2630 mounting plate using the (3) 8 x 32 x .5 flat head screws, nuts and washers provided. 2. The PIXORD 261/262 cameras require .“ of spacing to properly position the camera within the housing. Use (4) .” spacers provided in the hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. INSTALLING QUICK RELEASE BRACKETS SONY SNCRZ30 2539 Mounting Plate: 1. Attach the camera to the 2539 mounting plate using the (1) . x 20 bolt, washer and lockwasher provided. 2. The SNCRZ30 require 2” of spacing to properly position the camera within the housing. Use (4) 2” spacers provided in the hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Attach camera using this hole 2" INSTALLING QUICK RELEASE BRACKETS SONY SNCRZ50 2539 Mounting Plate: 1. Attach the SNCRZ50 camera to 2539 mounting plate using 3mm x 8mm bolt lockwashers provided. 2. The SONY SNCRZ50 require 2 . ” of spacing to properly position the camera within the housing. Use (4) 2” spacers plus (4) . “ spacers provided in the hardware packet. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Attach camera using this hole ." 2" INSTALLING QUICK RELEASE BRACKETS TOSHIBA IK-WB21A 2539 Mounting Plate: 1. Remove the quick release bracket from the camera. Using (4) 8 x 32 x 3/8 bolts and star washers attach the quick release place to the 2539 mounting plate. 2. The Toshiba 1K-WB21A requires 3” of spacing to properly position the camera within the housing. Use (4) 2” spacers plus (4) 1” spacers provided in the hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Attach camera using these (4) holes 1" 2" INSTALLING THE HOUSING ASSEMBLY: WIRING INSTRUCTIONS Be sure the bracket is properly and securely mounted to a supporting structure capable of rigidly holding the weight of the entire unit. RJ45 ! BNC NOTE: This unit is designed for operation in an upright position. Installing the housing upside down may cause damage to the internal equipment, and will void the warranty. (Large) Power (Small) Alarms INSTALLING PENDANT MOUNT 1. This unit includes a 1." NPT housing for a standard 1." NPT pipe. The housing can be used with other brackets designed with 1." male pipe threads, such as the WM20G wall mount bracket. 2. Attach the housing coupling. Wiring Color Code Power and Control Inputs AFTER CAME...
Эта инструкция также подходит к моделям:Видеонаблюдение - IP ReadyTM Series Video Alarm FDP75C12N (1.85 mb)