Оценок - 5, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
2 Press BATT RELEASE and slide the battery pack up. You can check the battery’s current charge level and its current remaining recording time both during charging or when the power is turned off. The remaining recording time in the selected recording format appears. 1 Set the POWER switch to OFF (CHG). 2 Open the LCD panel and adjust the angle. 3 Press DISPLAY/BATT INFO. The battery information appears for about 7 seconds. Keep the button pressed to view it for about 20 seconds. BATTERY INFO 50%0% 100% BATTERY CHARGE LEVEL REC T I ME AVA I LABLE LCD SCREEN: V I EWF I NDER: 115 min 125 min A Battery charge level: Displays approximate remaining amount of power left in the battery pack. B Possible recording time using the LCD panel. C Possible recording time using the viewfinder. Getting started Charging time Approximate number of minutes required when you fully charge a fully discharged battery pack at 25°C (77°F). (10 – 30°C (50 – 86°F) recommended.) Battery pack NP-F570 (supplied) 260 NP-F770 370 NP-F970 485 b Note • NP-F330/F530/500/510/710 battery packs cannot be used with your camcorder. Recording time Approximate number of minutes available when you use a fully charged battery pack at 25°C (77°F). Recording in the HDV format Battery pack Continuous recording time Typical recording time NP-F570 (supplied) 115 125 125 65 65 65 NP-F770 235 260 260 130 130 130 NP-F970 365 390 390 200 205 205 Recording in the DV format Battery pack Continuous Typical recording recording time time NP-F570 120 65 (supplied) 135 70 130 65 NP-F770 250 135 280 140 275 140 NP-F970 380 205 415 215 410 215 • The top figures show an approximate number of minutes when the LCD BACKLIGHT switch is set to ON. • The middle figures show an approximate number of minutes when the LCD BACKLIGHT switch is set to OFF. • The bottom figures show an approximate number of minutes when recording with the viewfinder. • “Typical recording time” means an approximate number of minutes when recording while you repeatedly record, start/stop, move the POWER switch to change the power mode, and zoom. The actual battery life may be shorter. z Tip • You can also use NP-F550/F730/F750/F960 battery packs. After charging these battery packs, make a trial recording with them before an actual recording to see the recording time. The recording time varies depending on the environment where the camcorder is used. Press DISPLAY/BATT INFO to display the recording time on the screen. Playing time Approximate number of minutes available when you use a fully charged battery pack at 25°C (77°F). HDV format pictures Battery pack LCD panel opened* LCD panel closed NP-F570 (supplied) 175 200 NP-F770 360 410 NP-F970 545 620 DV format pictures Battery pack LCD panel LCD panel opened* closed NP-F570 200 235 (supplied) NP-F770 415 480 NP-F970 630 725 * With the LCD BACKLIGHT switch set to ON. b Note • The power will not be supplied from the battery pack when the AC Adaptor is connected to the DC IN jack of your camcorder, even if its mains lead is disconnected from the wall socket. • The recording and playback time will be shorter when you use your camcorder in low temperature. ,continued Getting started Getting started • The CHG (charge) lamp flashes during charging, or the battery information will not be correctly displayed in following conditions. – The battery pack is not attached correctly. – The battery pack is damaged. – The battery pack is fully discharged. (For Battery information only.) Using an outside power source You can use the AC Adaptor as the power source when you do not want the battery to run out. While you are using the AC Adaptor, the battery pack will not lose its charge even when it is attached to your camcorder. PRECAUTION Even if your camcorder is turned off, AC power (mains) is still supplied to it while connected to the wall socket via the AC Adaptor. Connect your camcorder as shown in “Step 2: Charging the battery pack” (p. 11). Step 3: Turning the power on You need to set the POWER switch to the respective power mode to record or play back pictures. When using this camcorder for the first time, the [CLOCK SET] screen appears (p. 16). While pressing the green button, set the POWER switch. The power turns on. • CAMERA: To record pictures. • VCR: To play or edit pictures. To turn off the power Set the POWER switch to OFF (CHG). Getting started Step 4: Adjusting the LCD panel and viewfinder Adjusting the LCD panel You can adjust the angle and brightness of the LCD panel to meet various recording situations. Even when there are obstructions between you and the subject, you can check the subject on the LCD screen during recording by adjusting the angle of the LCD panel. 180 degrees Up to about 100 degrees Open the LCD panel 180 degrees, then rotate it to the desired position. To adjust the brightness of the LCD screen Adjust the brightness by pressing LCD BRIGHT – or +. z Tip • If you rotate the LCD panel until it faces down, you can close and restore the ...