Войти:
Оценок - 2, средний балл: 4.5 ( )

Инструкция по эксплуатации Vermont Casting, модель LHERDV30

Производитель: Vermont Casting
Размер: 1.69 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


(Fig. 21) 2. Lift and unhook the glass frame at the top. Machine Screw Fig. 21 Remove glass frame. Latch FP1328 Log Installation and Burner Lava Rock FP1327.. 2. Remove logs from packaging. 1 . Remove glass frame. (See "Glass Removal" section) window frame removal 4/3/03 djt 3. Place logs according to the model instructions below: LHECDV20, LHERDV20 (Fig. 22) a. Place rear left log (JR7). Use the log's bottom holes to locate it onto one pin stud of the rear log bracket on the left and the other end of the log will sit on top of the lid of the left log support. b. Place rear right log (JR8). Use the log's bottom holes to locate it onto the two (2) pin studs of the rear log bracket on the right. c. Place the front left log (JR9). Position the log notch against the second grate from the left, and the other edge of the log on top of the rear left log notch. Ensure the log is secure in place. d. Place the front right log (JR10). Position the log notch against the third grate from the right, and the other edge of the log on top of the rear right log notch. Ensure the log is secure in place. 10004894 13 LHEDV Series Direct Vent Insert e. Place the burner lava rock on the front area of the burner housing. (Fig. 22) LHECDV30, LHERDV30 (Fig. 23) a. Place the rear center log (KR24). Use the log's bottom holes to locate it onto the two (2) pin studs of the rear log bracket on the center. b. Place rear left log (KR22). Use the log's bottom holes to locate it onto the two (2) pin studs of the rear log bracket on the left. c. Place rear right log (KR23). Use the log's bottom holes to locate it onto the two (2) pin studs of the rear log bracket on the right. d. Place the front left log (KR25). Position the log notch against the second grate from the left, and the other edge of the log on top of the rear left log notch. Ensure the log is secure in place. e. Place the front right log (KR26). Position the log notch against the third grate from the right, and the other edge of the log on top of the rear right log notch. Ensure the log is secure in place. f. Place the burner lava rock on the front area of the burner housing. (Fig. 23) JR9 JR7 JR8 JR10 LG285 Burner Lava Rock Front Grate Fig. 22 LHEC20 and LHER20 log and lava rock placement. KR22 KR25 KR24 KR23 KR26 Burner Lava RockFront Grate LG286 Fig. 23 LHEC30 and LHER30 log and lava rock placement. Large Lava Rock Placement The large lava rock provided with this fireplace should be placed on the firebox base on either side of the burner assembly. Under no circumstances should these lava rocks be placed on top of the burner assembly. Flame Adjustment (RN/RP Models) For fireplaces equipped with HI/LO valves, flame adjustment is accomplished by rotating the HI/LO adjustment knob located near the center of the gas control. (Figs. 24 or 25) ........ Turn counterclockwise to decrease flame height Turn clockwise to increase flame height Honeywell Valve Fig. 24 Flame adjustment knob for Honeywell Valve. Turn Turn clockwise counterclockwise to decrease to increase flame height flame height Fig. 25 Flame adjustment knob for SIT valve. FP390 FLAME ADJUSTMENT KNOB 11/21/96 LHEDV Series Direct Vent Insert First FiringFlame Characteristics It is important to periodically perform a visual check of the pilot and the burner flames. Compare them to the Figure 26 and Figure 27 or 28. If any of the flames appear abnormal call a service person. 3/8" - 1/2" SIT Pilot PSE Pilot F584-703 Fig. 26 Correct pilot flame appearance. Upon completing the gas line connection, a small amount of air will be in the lines. When first lighting unit with pilot light, it will take a few minutes to purge themselves of this air. Once the purging is complete, the pilot and burner will light and operate as indicated in the instruction manual. Subsequent lightings of the heater will not require such purging. When lit for the first time, the appliance will emit a slight odor for awhile. This is due to paint and lubricants used in the manufacturing process. After each lighting, vapor may condense and fog the glass; this moisture disappears within a few minutes of burning. LG287 Fig. 27 Correct burner flame appearance for LHEC20 and LHER20. LG288 Fig. 28 Correct burner flame appearance for LHEC30 and LHER30. 10004894 15 LHEDV Series Direct Vent Insert Lighting and Operating Instructions FOR YOUR SAFETY READ BEFORE LIGHTING instructions. • If you cannot reach your gas supplier, call the Fire Department C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call a qualified service technician. Applying force or any attempted repair may result in a fire or explosion. D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water. A. This heater has a pilot which must be ...

Эта инструкция также подходит к моделям:
Вентиляторы - LHECDV30 (1.69 mb)
Вентиляторы - LHERDV20 (1.69 mb)
Вентиляторы - LHECDV20 (1.69 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории