|
Фрагмент инструкции
d. Securely connect the blue wire and yellow wire from the downrod to the supply red (hot) wire using wire connector (supplied). After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black, blue and yellow leads on the other side of the outlet box. BLACK BLACK FAN WIRE LISTED OUTLET BOX LIGHT CONTROLGREEN WIRE (GROUND) FROM HANGER BRACKET TO 120 VOLT SUPPLY WHITE GROUND GROUND GREEN WIRE (GROUND) FROM HANGER BALL LISTED WIRE CONNECTOR (4) GROUND WIRE WHT. EMERSON FAN CONTROL BLACK (HOT) BLUE RED THREE - CONDUCTOR CABLE WITH GROUND BETWEEN CEILING AND WALL OUTLET BOXES Figure 29 23. To complete the ceiling fan assembly, proceed to the “FINAL ASSEMBLY” section. WARNING ! Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. FINAL ASSEMBLY 1. Screw the two 1-1/4” threaded studs (provided) into the tapped holes in the hanger bracket. 2. Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover (Figure 30). 3. Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs (supplied). (Figure 30.) Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the pipe. KNURLED KNOB CEILING COVER LOCKWASHERS (2) 1-1/4" THREADED STUD Figure 30 WARNING ! To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling. 4. Screw in three 40-watt (maximum) candelabra base lamps into the uplight sockets on top of the fan housing assembly. 11 5. Slip the pull chain through the bushing in the switch housing cover assembly (Figure 31). Position the cover assembly on the switch housing assembly with the reversing switch lever positioned in the slot provided. Secure the cover assembly to the switch housing assembly using four 8-32 x 3/8” flat head screws (provided). 6. Slip the switch pull chain through the hole in the pendant (supplied), then secure the pendant by snapping the coupling (supplied) onto the end of the chain. TRIM MEDALLION BUSHING SWITCH HOUSING ASSEMBLY SWITCH HOUSING COVER ASSEMBLY REVERSING SWITCH LEVER 8-32 X 3/8" FLAT HEAD SCREW (4) PULL CHAIN Figure 31 Using Your Ceiling Fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. 2. When controlled by a wall switch check the operation of the fan by gently pulling on the 4-position speed control pull chain switch. The operating sequence is as follows: SPEED CONTROL SWITCH PULL CHAIN REVERSING SWITCH THREE-SPEED 1st Pull — HIGH 2nd Pull — Medium 3rd Pull — Low 4th Pull — OFF 3.When operated by an Emerson Remote Control, check operation of fan and light in accordance with the Remote Control Owner’s Manual. 4. If airflow is desired in opposite direction, turn your fan off and wait for the blades to stop turning. Then slide the reversing switch to the opposite position and turn fan on again. The fan blades will turn in the opposite direction and reverse the airflow. Attaching Light Kit To install an Emerson accessory light kit, remove the four screws securing the switch housing cover assembly to the switch housing. Remove the trim medallion from the bottom of the switch housing cover (Figure 32). Attach the light kit to the switch housing cover assembly with the lockwasher and nut supplied with the light kit (Figure 33). Install the light kit in accordance with the Emerson light kit Owner's Manual. REMOVE FLAT HEAD SCREW (4) SWITCH HOUSING COVER ASSEMBLY REMOVE HEX SCREW REMOVE TRIM MEDALLION Figure 32 WARNING ! To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. LIGHT KIT SWITCH HOUSING COVER ASSEMBLY LOCKWASHER AND NUT (SUPPLIED WITH LIGHT KIT) Figure 33 12 ! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections in the switch housing. 1. Check main and branch circuit fuses or circuit breakers. WARNING: Make sure main power is turned off. 2. Check line wire connections to fan and switch wire connections in the switch housing. ! 2. Fan sounds noisy. 1. Blades not attached to fan. 2. Loose screws in motor housing. 3. Screws securing fan blade flanges to motor hub are loose. 4. Wire connectors inside switch housing rattling. 5. Screws holding blades to flanges are loose. 1. Attach blades to fan before operating. 2. Check to make sure all screws in motor housin...
Эта инструкция также подходит к моделям:Вентиляторы - CF2500HTW01 (317.97 kb)
Вентиляторы - CF2500S01 (317.97 kb)
Вентиляторы - CF2500TG01 (317.97 kb)