Оценок - 4, средний балл: 4 ( )

Производитель: Emerson Размер: 317.97 kb Название файла: Язык инструкции:

20. Position the receiver (supplied with the SW330 Remote Control or SW350 Wall Control) by passing the opening in the receiver over the downrod (Figure 15). HANGER BRACKET HANGER BALL CEILING COVER SW375 RECEIVER FLAT SIDE OPEN SIDE 1/8" FOAM ADHESIVE PAD Figure 15 WARNING ! To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation. 21. Connect the black wire from the wiring harness to the black (hot) supply wire (Figure 4). Connect the white wire from the wiring harness to the white (neutral) supply wiring. Connect the green ground wires from the hanger bracket and the hanger ball to the supply ground wire. Use wire connectors supplied with your ceiling fan. WARNING ! Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. 7 22. Securely connect the wiring harness connector to the receiver connector, and connect the blue and yellow wires to the blue and yellow wires from the receiver (Figure 4). 23. Turn the receiver so that the flat side aligns with the open side of the hanger bracket (Figure 15). Fold and position the wires into the space above the hanger ball and into the outlet box. 24. Feed the wires and connectors around the outside of the receiver, through the open side of the hanger bracket, and into the outlet box. Slide the receiver up and over the hanger bracket. Remove the backing on the foam adhesive pads and press the receiver against the ceiling. 25. To complete the ceiling fan assembly, skip to the “FINAL ASSEMBLY” section of this Owner’s Manual. SECTION B Assembly Instructions for Installing the CF2500 Ceiling Fan with Any Other Control Method (excluding the SW375 Receiver, SR330 Remote Control or the SW350 Wall Control) 1. Position the fan motor and housing assembly in the lower foam packing so that the top of the motor is facing you. 2. Separate, untwist and unkink the four motor leads. 3. Obtain the hanger ball/downrod assembly and remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 16). Remove the pin from the downrod , then remove the hanger ball. Retain the pin and hanger ball for reinstallation in step 9. SETSCREWCLEVIS PIN HANGER BALL DOWNROD Figure 16 4. Push the uplight yellow lead assembly connector through the downrod (Figure 17) until it extends about 4”. 5. Cut the yellow lead approximately 3” from the end of the pipe. Strip insulation 1/2” from end of the wires. 6. Using the wire connector supplied, connect the uplight yellow lead assembly to the yellow lead from the fan motor and housing assembly (Figure 18). UPLIGHT YELLOW CUT 4" LEAD ASSEMBLY HERE DOWNROD 3" Figure 17 7. Route the white, blue, and black motor leads through the downrod. Fold the yellow, red, and brown wires into the slot in the motor coupling, slide the downrod down the wires and seat the downrod in the motor coupling (Figure 18). 8. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 18). The clevis pin must go through the holes in the motor coupling and the holes in the downrod . Push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed. WARNING ! It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. SETSCREW CLEVIS PIN MOTOR COUPLING DOWNROD HAIRPIN CLIP MOTOR COUPLING HAIRPIN CLIP CLEVIS PIN DOWNROD CLEVIS PIN Figure 18 9. Install the setscrew (supplied in loose parts bag) in the motor coupling and tighten using the 5/32" setscrew wrench (supplied) (Figure 19). 8 ! WARNING MOTOR DOWNROD SETSCREW Figure 19 10.Screw two 1” threaded studs (provided) into the motor (Figure 20). Leave approximately 7/8” of the stud extending above the motor. Slide the motor cover over the downrod and rotate the cover until the threaded studs protrude; install two knurled knobs (supplied) to secure the cover. NOTE: Make sure the red and brown leads are separately capped with wire connectors. Make sure red, brown, and yellow wire connectors are completely inside motor coupling cover and not pinched between the motor coupling cover and motor. KNURLED KNOB 1" THREADED STUD MOTOR COUPLING COVER 7/8"MOTOR WIRE CONNECTORS WIRE CONNECTOR RED LEAD BROWN LEAD YELLOW LEAD Figure 20 11.Position th...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: