Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Main ON/OFF power switch: This switch is located at the furthest right corner on the control panel when looking at the back of the unit. Turn the switch to ON and unit will be ready to operate. The "|" indicates ON and "O" indicates OFF. 2. Heater Switch and Control Dial: The heater switch has a sun directly below it. To turn the heater on, flip the Heater Switch to ON position (the "|" indicates ON and "O" indicates OFF). The Control Knob has a thermometer below it. Turn the dial clockwise past the number 8. You should elements and should not occur again. 4. Flame Control Dial: This dial controls the intensity of the flame. Light Adjustment Dial Main Power SwitchFlame Control Dial Heater SwitchHeat Control Dial Grounding Pin Adapter CLEANING AND MAINTENANCE WARNING: Always discon- nect power and allow the heater to cool before performing any cleaning,maintenanceorreloca- tion of this heater. Turn controls to OFF and remove plug from outlet or turn off circuit breaker to heater. Turn off heater and circuit breaker to heater before performing any cleaning and/or maintenance. Al- low heater to cool completely. BULB REPLACEMENT hear a small clicking sound indicating the heater has started and heat will emit the from the vents at the top of the unit. To turn off heater, turn the temperature dial counter clockwise past number 1 and flip the Heater Switch to OFF position. To increase the desired temperature, turn the temperature dial clockwise towards Number 8. WARNING: The halogen light bulbs in your unit can become extremely hot. Allow at least 10 minutes between turning off the heater and removing the light bulbs to avoid accidental burns. 117191-01A CLEANING AND MAINTENANCE Continued There are a total of 7 halogen light bulbs (type GX6.35 rated 120 volts, 35 watts) in your unit. • 2 bulbs provide illumination for the ember bed beneath the log set • 2 bulbs provide illumination for the flame generation assembly • 1 bulb provides illumination for the top contrasting light • 2 bulbs for replacement Most halogen light bulbs are rated to last approximately 1800 hours. Like all light bulbs, halogen bulbs require periodic replacement. When the bulbs in your unit have burned out you will notice or more of the following: • Contrasting light is dark • Flame is dim or dark in certain areas • Log set ember bed appears dim or dark in certain areas WARNING: Do not install replacement bulbs that exceed specified maximum watts. Your unit must be opened in order to replace the light bulbs. To reduce the number of times you need to open the unit, replace all bulbs at the same time. Removing Front of Unit 1. Unplug unit from the power supply. 2. Remove the four screws in front of the unit that secure the grill to the main frame (see Figure 4). 3. Four clips hold the front panel to the frame of the unit. Lift the front panel upwards until the clips disconnect. Remove and place face up on the floor. Remove Remove Front Panel Screws Replacing Top Contrasting Bulb 1. The top contrasting light is mounted on the underside of the top “shelf”. 2. Carefully remove spring clip. Hold socket and pull out the old bulb. 3. Hold socket and push in new bulb (DO NOT exceed wattage). Replace spring clip. Front of Stove Top Contrasting Bulb Figure 5 - Replacing Top Contrasting Bulb Replacing Log Set Ember Bed Bulbs 1. Remove two screws from grate that secures log set to frame. 2. Fromthebottom,liftupthelogsetemberbedand remove it from the unit (do not pull up on logs). 3. Remove spring clip from bulb. Hold socket and pull out old bulb. 4. Hold socket and push in new bulb. Replace spring clip. Glass Bulb with Spring Clip 117191-01A 5 Figure 4 - Stove Front Panel R...
Эта инструкция также подходит к моделям:Варочные панели - CGESBM (375.22 kb)
Варочные панели - CGESBM (375.22 kb)
Варочные панели - CGESBM (375.22 kb)
Варочные панели - CGESBM (375.22 kb)