Оценок - 0, средний балл: 5
(
)
)
|
Фрагмент инструкции
• Note the serial number on the bottom of your radio and write this number in the space provided on Page 2 of this manual. • Place your radio on a level surface such as a table, desk or shelf, convenient to an AC outlet, out of direct sunlight, and away from sources of excess heat, dirt, dust, moisture, humidity, or vibration. NOTE: Do not place this radio on a metal shelf, metal table, or other metal surface as this may interfere with AM reception. • Unwind the AC power cord and extend it to its full length. The FM antenna is built in to this cord. It must be fully extended to provide the best FM reception. POWER SOURCE This radio is designed to operate on normal 120V 60Hz AC power only. Do not attempt to operate the radio on any other power source. You could cause damage to the radio that is not covered by your warranty. This radio should be connected to an AC outlet that is always ‘live’. Do not connect it to an outlet that is controlled by a wall switch. When the power to the radio is interrupted, the built in lithium battery takes over to maintain the time and alarm settings. To maximize the life of the lithium battery keep the radio connected to a ‘live’AC outlet at all times You will note that this system is equipped with a polarized AC power plug having one blade wider than the other. This is a safety feature. If this plug does not fit into your existing AC outlet, do not try to defeat this safety feature by filing the wide blade to make it fit into your outlet. If this plug will not fit into your outlet, you probably have an outdated non-polarized AC outlet. You should have your outlet changed by a qualified licensed electrician. 4 AC Plug AC Outlet CKS2288_ib_092302.p65 4 23/9/2002, 11:53 5 LOCATION OF CONTROLS AND INDICATORS Top Panel 1. MONTH/DATE Setting Button. 2. TIME setting Button. 3. ALARM MODE Button. (weekdays/weekends/everyday alarm) 4. ALM(Alarm) 1 Setting Button. 5. ALM(Alarm) 2 Setting Button. 6. SNOOZE/SLEEP OFF Button. 7. SET - Button. 8. SET + Button. 9. TIME ZONE Button. 10. SLEEP Button. 11. RADIO ON/OFF Button. Left Side 12. ALARM 1 Selector Switch. (RADIO/BUZZER/OFF) 13. ALARM 2 Selector Switch. (RADIO/BUZZER/OFF) 14. Display DIMMER(HIGH/LOW) Switch. Right Side 15. VOLUME Control. 16. BAND(AM/FM) Switch. 17. TUNING Control. Front Panel 18. ALM(Alarm) 2 ‘On’ Indicator. 19. ALM(Alarm) 1 ‘On’ Indicator. 20. AM Indicator. 21. Time Display. 22. Day Indicators. 23. BATT. LOW Indicator. 24. Month/Date Display. 25. Lighted Dial Pointer. Back Panel 26. Back Up Battery Compartment. 27. AC Power Cord. 27 1 2 3 4 5 6 7 8 9 10 11 26 13 14 18 19 20 21 23 12 24 15 16 25 22 17 CKS2288_ib_092302.p65 5 23/9/2002, 11:54 OPERATING INSTRUCTIONS SETTING THE TIME, THE FIRST TIME IMPORTANT: The first time you connect your new SmartSet® clock radio to the AC outlet the internal computer will automatically set the time correctly for the Eastern Time Zone, which is the initial default setting. The display will scan for a few seconds and then set the correct month, date, day and time in the Eastern zone. If you live in the Eastern Time zone, there’s nothing else to do. Your clock is set correctly and running. If you do not live in the Eastern Time zone you must change the default zone display to your own zone. You only do this one time and the SmartSet® will remember the new default zone setting and will always return to that setting after a power interruption. There are 7 time zones programmed into your SmartSet® clock radio as follows: ZONE 01 — Atlantic Time ZONE 02 — Eastern Time ZONE 03 — Central Time ZONE 04 — Mountain Time ZONE 05 — Pacific Time ZONE 06 — Yukon Time ZONE 07 — Hawaiian Time To change the default time zone display, depress the TIME ZONE button. The word “ZONE”appears in the main display, and the number “02”will appear on the month/date display, indicating that the default zone is Zone 02, Eastern Time. Hold the TIME ZONE button and then press either the SET + or SET – buttons until your own time zone appears on the display, then release the buttons. The clock display will change to the correct time in the time zone you selected. The clock will always return to the correct time in the zone you selected after every power interruption. If you move to a different time zone, simply change the default zone display to the new zone and the SmartSet® will remember that setting for you. 6 CKS2288_ib_092302.p65 6 23/9/2002, 11:53 DATE DISPLAY The correct month and date appear in the small display. The month and date are expressed numerically in the MM/DDformat. For example, May 21st will be displayed as (5. 21). This display adjusts automatically for months of different lengths. For example, at midnight on February 28th (2. 28), the display will automatically change to March 1st (3. 1), unless it is a Leap Year, in which case the display will change to February 29th (2. 29). YEAR DISPLAY To see the correct year, depress the TIME and MONTH/DATE buttons together. The small display changes from ‘...