Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
For easier use, always use the Ultracord system. Integral anti-scale system (depending on model) Your iron is equipped with an integral anti-scale system – fig.11. This system will help to provide: • a better ironing quality with a constant flow of steam, • lasting performance from your appliance. Auto-Stop safety feature (depending on model) • The electronic system cuts off the electric power and the Auto-Stop warning When the Auto-Stop light flashes if the iron is left vertically on its heel for more than 8 minutes, or in warning light is on, it is normal for the a horizontal position for more than 30 seconds – fig.12. thermostat light to • To restart the iron, just move it gently until the warning light stops flashing. remain off. Anti-drip function (depending on model) When using the iron for • If the soleplate temperature is too low, the iron will not produce steam because the first time, allow 2 of the anti-drip technology which prevents droplets of water leaking from the minutes for steam to be soleplate. produced. Maintenance and cleaning Cleaning the anti-scale valve (once a month) • Unplug your iron and empty the water tank. • To remove the anti-scale valve, pull it up – fig.13. • Soak the valve in a cup of white spirit vinegar or plain lemon juice for hours – fig.14. • Rinse the valve under running water. • Replace the anti-scale valve. Be careful ! - Never touch the end of the valve. - The iron will not function without the anti-scale valve. Self-cleaning The self-cleaning • Fill the tank of your iron with untreated tap water. Stand the iron on it’s heel with function helps to slow the thermostat set to “Max” and heat it up. down scaling in your • When the thermostat light goes out, unplug the iron and hold it in a horizontal iron. position, over a sink. Remove the anti-scale valve – fig.13. In order to extend the life of your iron, use the • Shake the iron gently, over the sink, until some of the water in the water tank (with Self-Cleaning function the impurities) has flowed out through the soleplate – fig.15. once a month. • At the end of the operation, push the anti-scale valve back into position. • Unplug the iron, and when the soleplate is just warm, wipe it with a soft cloth. Cleaning the soleplate • While the soleplate is still slightly warm, clean it by wiping over it with a damp Never use abrasive or non-metallic cloth. aggressive products on the soleplate. Storing your iron • Unplug the iron and wait for the soleplate to cool down. • Close the Ultracord System and lock it by positionning the ring indicator (depending on model) onto . • Empty the water tank and set the steam control to “0”. A little water may remain in the tank. • Wind the cord around the heel at the back of the iron. Store the iron on its heel – fig.16. If there is a problem GB PROBLEM POSSIBLE CAUSES SOLUTIONS Water drips from the holes in the soleplate. The chosen temperature is too low and does not allow for the formation of steam. Position the thermostat in the steam range (from •• to MAX). You are using steam while the iron is not hot enough. Wait until the thermostat light goes out. You are using the Turbo button too often. Wait a few seconds between each use of the Turbo button. There is too much steam. Reduce the steam. You have stored the iron horizontally, without emptying it and without setting it to “0”. See the section "Storing your iron". Brown streaks come through the holes in the soleplate and stain the linen. You are using chemical descaling agents. Do not add any descaling agents to the water in the water tank. You are not using the right type of water. Perform a self-cleaning operation and consult the section "What water to use?" Fab...
Эта инструкция также подходит к моделям:Утюги - FV5210 (1.73 mb)
Утюги - FV5230 (1.73 mb)
Утюги - FV5260 (1.73 mb)