Оценок - 4, средний балл: 3.8 ( )

Производитель: ParaBody Размер: 490.12 kb Название файла: 99020193.pdf Язык инструкции:

Make sure that the Pulley Covers are turned so the small rims are inside the loop of Cable as shown. See assembly step 9, and make sure that the Cable is routed exactly as shown. Attach the Pulley Covers (88) and the 3 1/2" Pulley (27) to the Selector Plate (19) with the 3/8" x 2" Bolt (87) and a 3/8" Nylon Jam Nut (41). Rims Note: This section of cable must go over the top of the indicated pulley Wire Tie exactly as shownl The drawing at the right shows the correct route of 9 the Cable (25). Make sure that the Cable is routed exactly as shown. Note: The letters indicate the order in which the Cable is muted around the Pulleys. 25 B D G E 7 10.PulltheMomentArm(10)forward. Hold the lower and of the Left Press Arm (52) in the upper end of the Moment Arm. The Left Press Arm must be turned so the Handle (12) is on the side shown. Attach the Left Press Arm with two 3/8" x 2 1/2" Bolts (44) and two 3/8" Nylon Locknuts (33). The Bolts must be Inserted from the side shown, or the BOBYLIFT will not function properly. Press a Small Bumper (91) onto the underside of the Handle (12). Assemble the Right Press Arm (11) in the same manner. 11. Insert the 114"x 2 1/2" Cardage Bolt (46) into the Seat Bracket (38). Attach the Seat Bracket to the Seat (14) with the two 1/4 x 3/4" Screws (47). Insert the 1/4" x 2 1/2" Carriage Bolt (46) into the indicated hole in the Seat Frame (8). The narrow end of the Seat must be facing the curved end of the Seat Frame. Tighten a 1/4" Nylon Jam Nut (55) with a 1/4" Flat Washer (40) onto the Carriage Bolt. Attach the other end of the Seat to the Seat Frame with a 1/4" x 2 1/2" Screw (32) and a 1/4" Flat Washer (40). 12. Attach the Seat Frame (8) to the Front Ul_dght (7) with the 5/16" x 2 3/4" Bolt (78) and a 5/16" Nylon Locknut (73). The Moment Arm (10) must be in front of the indicated tube on the Seat Frame. Attach the Seat Braces (21) to the Seat Frame (8) witha3/8" x2 3/4" Bolt (85) and a 3/8" Nylon Locknut (33). Tighten the Nylon Locknuts on both ends of the Seat Braces. 13. Hold the Cable (25) under the indicated 3 1/2" Pulley (27). Hold the 1/2" x 1" Sleeve (89) between the small holes in the lower end of the Leg Lever (9). Attach the Sleeve with the 1/4" x 1 3/4" Bolt (43) and a 1/4" Nylon Jam Nut (55). The Cable must be between the Pulley and the Sleeve. lO 12 11 52 12 33 73 7 8 10" 13 25 14. InsertonePadTube(13)intotheSeatFrame(8). 14 InserttheotherPadTubeintotheLegLever(9). Slide two 6" Pads (24) onto each Pad Tube (13). 24 24 15. Pivot the Link Tube (16) on the Left Arm (5) onto 15 the end of the Link Tube Axle (17). Attach the Link Tube to the Link Tube Axle with a 114"x 1 1/4" Bolt (49) and a 1/4" Acorn Nut (62). Tap a 1" x 1" Inner Cap (36) into the Link Tube (16). Attach the Link Tube (16) on the Right Arm (6) to the Link Tube Axle (17) in the same manner. 16 62 16. Make sure that all parts are properly tightened. The use of all remaining parts will be explained in USING THE BODYLIFT on page 11 of this user's man...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: