Оценок - 2, средний балл: 4.5 ( )

Производитель: Keys Fitness Размер: 490.12 kb Название файла: 99020193.pdf Язык инструкции:

• Read through each assembly step before you begin. • For help identifyingthe small pads used in assembly, remove the PART IDENTIFICATION CHART from the center of this user's manual. Note: Some small parts may have been pre- attached for shipping purposes. If a part is not found in the parts bag, check to see if it has been pre-attached. . Before you begin, read the information and Instructions at the top of this page. Note: The BODYLIFT requires a minimum ceiling height of 7 1/2 feet. Insert the four 3/8" x 2 1/2" Carriage Bolts (70) up through the indicated holes in the Base (1). , Slide the Rear Upright (2) onto the four 3/8" x 2 1/2" Carriage Bolts (70) in the Base (1). Make sure that the Rear Upright is turned as shown. Tighten a 3/8" Nylon Jam Nut (41) onto each Carriage Bolt. • As you assemble the BODYLIFT, make sure that all parts are oriented exactly as shown in the drawings. • Tighten all parts as you assemble them, unless instructed to do otherwise. THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY: Two (2) adjustable wrenches One (1) standard screwddver One (1) phillips screwdriver One (1) rubber mallet Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches. 70 Insert These Carriage Bolts First 70 2 4 Attach the Footrest (35) to the Front Upright (7) 3. 3 with two 3/8" x 2 3/4" Bolts (85), two 3/8" Flat Washers (53), and two 3/8" Nylon Locknuts (33) as shown. 35 . Remove the 3/8" x I 112"Carriage Bolt (80) and the 3/8" Nylon Jam Nut (41) from the indicated brackets on the Front Upright (7). Remove the loop of Cable (25) from the brackets. Lubricate the 3/8" x 1 1/2" Carriage Bolt (80). Attach the Selector Plate (19) to the brackets on the Front Upright (7) with the Carriage Bolt and the 3/8" Nylon Jam Nut (41). . With the help of a second person, hold the Front Upright (7) in front of the Rear Upright (2), with the Selector Plate (19) between the sides of the Rear Upright. Insert the loopofCable (25) through the sides of the Rear Upright (2). Slide a Weld Cover (63) onto each of the indicated axles on the Front and Rear Uprights (7, 2). The Weld Covers must be turned so the open sides are facing the Uprights. Lubricate the axles. Slide a Long Riser (3) onto the axles. The Long Riser must be turned as shown. Hold a 3/4" Retainer (57) and a 3/4" Retainer Cap (59) against the end of one of the axles. The teeth on the Retainer must bend toward the Retainer Cap (see the inset drawing). Tap the Retainer and Retainer Cap onto the axle. Tap a 3/4" Retainer (57) and a 3/4" Retainer Cap (59) onto the other axle. Attach the other Long Riser (3) to the lower axles on the other side of the Front and Rear Uprights (7, 2) in the same manner. 85 53 4 19 41 57 59 7 Axle Teeth cate 5 . 7o Slide a Weld Cover (63) onto each of the indicated axles on the Front and Rear Uprights (7, 2). The Weld Covers must be tumed so the open sides are facing the Up...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: