Войти: 3. Scan the hex digit bar codes for 4, 1 and 4, 2 on the inside back cover of this manual. 22 QS2500 4. Scan the Store Settings bar code on the inside back cover. 5. Repeat the same procedure for the G2 characters. 6. Scan the Exit bar code. 7. Insert the data group 1–4 position. (page 24.) Start Program $ Option Bar Code Option Alphanumeric Entry Prefix None 00* 1–22 characters 00–ffhex ASCII code None 00 Suffix 1–22 characters 00–ffhex ASCII code
ENTER/EXIT PROGRAMMING MODE DEFAULT Country Mode = U.S. Country Mode = Belgium Country Mode = Britain Country Mode = Croatia Supports only the interfaces listed in the Country Mode feature description. Supports only the interfaces listed in the Country Mode feature description. Country Mode = Czechoslovakia Gryphon™ I GD4100 Country Mode Country Mode — continued ENTER/EXIT PROGRAMMING MODE Country Mode = Denmark Supports only the interfaces listed in the Country Mode feature description. Country
Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy Gryphon™ Dx30/Mx30 Ed.: 09/2006 This manual refers to software version 3.1.0 and later ALL RIGHTS RESERVED Datalogic reserves the right to make modifications and improvements without prior notification. Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the use of this material. Product names mentioned herein are for identificatio
4.8 CHANGING DEFAULT SETTINGS Once your reader is setup, you can change the default parameters to meet your application needs. Refer to the preceding paragraphs for initial configuration in order to set the default values and select the interface for your application. In this manual, the configuration parameters are divided into logical groups making it easy to find the desired function based on its reference group. The first four groups are for Standard Interface parameter configuration: RS232
During this process a series of brief “ticks” indicates that reading is proceeding correctly. ADVANCED FORMATTING NOT FOR PEN INTERFACES • CONCATENATION • • ADVANCEDFORMATTING • Please follow the setup procedure carefully for these parameters. NOTE The Advanced Formatting parameters may not be compatible with the IBM USB POS interface selection. NOTE 1. Read the Enter Configuration code ONCE, available at the top of page. 2. Read configuration codes precisely following the numbered procedure giv
Use this selection onlyifyou must constantly read a wide variety of symbologies. Turn to the following pages for enabling additional symbology specific options. Disable All Symbologies — disables all symbologies1. The scanner will only recognize the programming labels contained in this manual while you are in Programming Mode. Enable UPC/EAN — tells the scanner to recognize UPC-A, UPC-E, EAN- 8, and EAN-13. If you enable this symbology, additional options for symbology expansion and reading a
(119 g) Color Black or White Electrical Characteristics Voltage & Current QD2110 4-14 VDC QD2130 5.0 VDC +/-10% 180mA @ 5V Typical Idle 345mA @ 5V Typical Scanning Performance Characteristics Light Source 617nm LEDs Roll (Tilt) Tolerance ± 45° from normal Pitch Tolerance ± 65° Skew (Yaw) Tolerance ± 65° Scan Angle 43° ± 3° Depth of Field 4.0 mil 3.0 - 9.5 cm 5.0 mil 2.3 - 14 cm 7.5 mil 1.5 - 26.5 cm 10 mil (80% UPC) 1.3 - 37.5 cm 13 mil (100% UPC) 2.5 - 46.5 cm 15 mil to 48 cm 20 mil to 59 cm Mi
EAN 8 IAAG1oI .. EAN 13 IAAH1rI .. UPC A IAAI1uI .. UPC E IAAJ1xI NO CHECK DIGIT TRANSMISSION EAN 8 IAAG0kI EAN 13 IAAH0nI UPC A IAAI0qI UPC E IAAJ0tI Enter Configuration Exit and Save Configuration I$+;I CODE SELECTION I$-?I CONVERSION OPTIONS UPC E to UPC A conversion IAAAAI UPC A to EAN 13 conversion IAACEI Enable only ISBN conversion IAP1nI Enable both ISBN and ISSN conversion IAP3tI UPC E to EAN 13 conversion IAABCI EAN 8 to EAN 13 conversion IAAD"I Enable only ISSN conversion IAP2qI Disabl
Barcode Label A label that carries a barcode and can be affixed to an article. Baud Rate A unit used to measure communications speed or data transfer rate. CDRH (Center for Devices and Radiological Health) This organization (a service of the Food and Drug Administration) is responsible for the safety regulations governing acceptable limitations on electronic radiation from laser devices. Datalogic devices are in compliance with the CDRH regulations. Code Positioning Variation in code placement t
192 I 2 of 5 Check Character Calculation ................................................................................ 193 I 2 of 5 Check Character Transmission ............................................................................. 194 I 2 of 5 Minimum Reads ................................................................................................. 195 2 of 5 Decoding Level .................................................................................................... 196 I
