Оценок - 12, средний балл: 4.1
(
)
)
|
Фрагмент инструкции
(119 g) Color Black or White Electrical Characteristics Voltage & Current QD2110 4-14 VDC QD2130 5.0 VDC +/-10% 180mA @ 5V Typical Idle 345mA @ 5V Typical Scanning Performance Characteristics Light Source 617nm LEDs Roll (Tilt) Tolerance ± 45° from normal Pitch Tolerance ± 65° Skew (Yaw) Tolerance ± 65° Scan Angle 43° ± 3° Depth of Field 4.0 mil 3.0 - 9.5 cm 5.0 mil 2.3 - 14 cm 7.5 mil 1.5 - 26.5 cm 10 mil (80% UPC) 1.3 - 37.5 cm 13 mil (100% UPC) 2.5 - 46.5 cm 15 mil to 48 cm 20 mil to 59 cm Minimum Element Width 3 mil Print Contrast Minimum 15% minimum reflectance Product Reference Guide Item Description Decode Capability UPC/EAN/JAN, P2 /P5 GS1-128 add-ons; Code 39; Code 39 Full ASCII; Code 32 (Italian Pharmacode); Code 128; ISBT 128; I 2 of 5; Standard 2 of 5; Code 11; Codabar; GS1-128; Code 93; MSI; GS1 DataBar Omnidirectional, GS1 DataBar Limited, GS1 DataBar Expanded; EAN 13 ISBN; Datalogic 2 of 5; Follet 2/5; Code 4, code 5. Interfaces Supported RS-232 Std., RS-232 Wincor-Nixdorf, RS-232 OPOS, IBM 46xx (ports 5B and 9B), USB Com Std., USB Keyboard, USB Alternate Keyboard, USB Keyboard Apple, USB-OEM, Keyboard Wedge (AT with or w/o Alternate Key, IBM AT PS2 with or w/o Alternate Key, PC-XT, IBM 3153, IBM Terminals 31xx, 32xx, 34xx, 37xx make only and make break keyboard, and Digital Terminals VT2x, VT3xx and VT4xx). User Environment Operating Temperature 32° to 122° F (0° to 50° C) Storage Temperature -40° to 158° F (-40° to 70° C) Humidity 5% to 95% relative humidity, non-condensing Drop Specifications Withstands multiple 5 ft./1.524 m drops to concrete. Ambient Light Immunity Immune to direct exposure of normal office and factory lighting conditions, as well as direct exposure to sunlight. Contaminants Spray/rain Dust/particulates IEC 529-IPX2 IEC 529-IP5X Beeper Volume User-selectable: three levels Beeper Tone (frequency) User-selectable: three tones Electrostatic Discharge Conforms to ±20 kV air/direct discharge and ±8 kV of contact discharge. Regulatory Electrical Safety USA: UL 60950, Canada: CAN/CSA-C22.2 No. 60950, EN60950/ IEC60950, NOM-019-SCFI EMI/RFI FCC Part 15 Class B, ICES-003 Class B, European Union EMC Directive, Australia Class B, Taiwan EMC, Japan VCCI/MITI, Korea KCC QuickScan® QD2100 Standard Cable Pinouts Standard Cable Pinouts Figure 7 and Table 36 provide standard pinout information for the imager’s cable. Figure 7. Standard Cable Pinouts Cable Clip (Latch) To Host Cable Cable Strain Relief Bottom of Imager Interface Cable Port Pin 1 Pin 10 The signal descriptions in Table 36 apply to the connector on the imager and are for reference only. Table 36. Standard Cable Pinouts — Imager Side Pin RS-232 OEM USB Keyboard Wedge 1 RTS (out) 2 D+ CLKIN (KBD side) 3 DDATAIN (KBD side) 4 GND GND GND GND 5 RX 6 TX 7 VCC VCC VCC VCC 8 IBM_B CLKOUT (PC side) 9 IBM_A DATAOUT (PC side) 10 CTS (in) Product Reference Guide NOTES QuickScan® QD2100 Appendix B Standard Defaults The most common configuration settings are listed in the “Default” column of Table 37. The settings in this table are as applied to a standard RS-232 interface. See Table 38 for a listing of default exceptions to this list as appled to other interface types. Page references are also provided for feature descriptions and programming barcodes for each parameter. A column has also been provided for recording of your preferred default settings for these same configurable features. Table 37. Standard Defaults Parameter Default Your Setting Page Number General Features Double Read Timeout 0.4 Second 17 Label Gone Timeout 160 ms 19 Power On Alert 4 Beeps 21 Good Read: When to Indicate After Decode 22 Good Read Beep Type Mono 23 Good Read Beep Frequency Medium 24 Good Read Beep Length 80 ms 24 Good Read Beep Volume High 26 Good Read LED Duration LED on until next trigger pull 27 Scan Mode Trigger Single 29 Stand Mode Triggered Timeout 0.5 Seconds 31 Scanning Active Time 5 Seconds 33 Flash On Time 1 Second 35 Flash Off Time 600 ms 37 Stand Mode Sensitivity Medium 39 Green Spot Duration 300 ms 40 Product Reference Guide Parameter Default Your Setting Page Number RS-232 Baud Rate 9600 41 Data Bits 8 Data Bits 43 Stop Bits 1 Stop Bit 44 Parity None 45 Handshaking Control Disable 46 RS-232/USB-COM Intercharacter Delay No Delay 48 Beep On ASCII BEL Disable 50 Beep On Not on File Enable 50 ACK Character ‘ACK’ 52 NAK Character ‘NAK’ 54 ACK NAK Timeout Value 600 ms 56 ACK NAK Retry Count 3 Retries 58 ACK NAK Error Handling Ignore Errors Detected 60 Indicate Transmission Failure Enable 61 Disable Character ‘D’ 62 Enable Character ‘E’ 64 Keyboard Wedge Country Mode U.S. Keyboard 68 Caps Lock State Caps Lock OFF 71 Numlock Numlock Key Unchanged 71 Send Control Characters Disable 72 Intercode Delay 100 ms 77 Intercharacter Delay No Delay 75 100 ms 78 USB Keyboard Speed 1 ms 79 USB-OEM USB-OEM Device Usage Handheld Scanner 82 QuickScan® QD2100 Parameter Default Your Setting Page Number Data Editing Global Prefix/Suffix No Global Prefix Global Suff...