Press START/STOP to continue, or press SPLIT/RESET/SET/ RECALL to reset the timer to its original setting. 10 F. The timer will beep for ten seconds when it reaches zero; stop the beeping sooner by pressing any button. How to Set and Use the Alarm How To Set Alarm A. Press SPLIT/RESET/SET/RECALL to begin setting procedures. HOURS will begin flashing. Press START/STOP to advance hours. Note AM or PM designation when setting hours. B. Press MODE; TENS OF MINUTES will begin flashing. Press START/ST

2 ©2004, 2005 Fluke Corporation, All rights reserved. Printed in U.S.A. All product names are trademarks of their respective companies Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 Table of Contents Section 1: General Information................................................................................... 1-1 1.1 Introduction .................................................................................................. 1-1 1.2 Descr

Replace the battery when the “Lo Batt” indicator shows in the display. Long life alkaline batteries are available from Fluke Biomedical. Any standard 9 V alkaline battery can be used in the Digital X-Ray Pulse Counter/Timer. To replace the battery, slide open the battery compartment on the bottom of the case. Remove the old battery, and install the new battery. Operation General Instructions Section 2 Operation 2.1 General Instructions Switch Settings The front panel selector/toggle switch on th

With this guide, you will: 1. Set up your blood pressure monitor and take a test reading. 2. Get ready to use your blood pressure monitor with HealthVault. 3. Connect your blood pressure monitor to your computer and upload your test reading to HealthVault. IMPORTANT: If you have not already created your HealthVault account and installed HealthVault Connection Center, please go to and follow the instructions. Let’s get started! Step 1: Set up your blood pressure monitor and take a test reading IM

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Operating the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Risk of Electrical Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Before Ta

. . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . 3 Battery Installation/Replacement . . . .. . . . . . . . . . . . . . . . . . . . 4 Preparing to Use the Monitor -Using the Monitor Attached to the Arm Cuff. . . . . . . . . . . . . . . . . . . . . . . . 5 -Using as a Tabletop Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Attaching the Arm Cuff and Posture During Measurement . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . 6

. . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . 3 Battery Installation/Replacement . . . .. . . . . . . . . . . . . . . . . . . . 4 Attaching the Wrist Cuff and Posture During . . . . . . . . . . . . . . . 4 Measurement Measurement . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . 5 Subsequent Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Automatic Power-off Function . . . . . .. . . . . . . . . . . . . . . . . . . . 6 Memory Reca

Attach one end of the coiled to the connector on the underside Aneroid (Figure 2). 2. Attach the other end of the coiled the metal connector) to the tube from and bladder (the tube without the bulb assembly). Figure 5 3. The cuff and bladder assembly can be stored in the basket on the back of the aneroid. Once mounted to the wall or affixed to a floor stand, the Omron Aneroid is ready for use. Connector Wall-Mount (for models 11-675D and 11-675DNL) : Coiled Tube 1. Hold wall-mount plate against

Tighten wing nut and slide the wall bracket into the wall-mount plate (Figure 4). Figure 4 3. The wall-mounted Omron Aneroid is now ready for use. Figure 3 Figure 2 240 240 220 180160140 120 100 80 60 40 20 260 280 300 mmHg SPHYGMOMANOMETER CERTIFIED MADE IN JAPAN Air Release Valve Bulb 4 5 ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS Floor Stand Kit models 11-685 Figure 6 Figure 7 1. Insert each of the five (5) wheel casters into each (5) legs of the five-legged base (Figure 6). 2. Insert the la

7. While holding the aneroid and small hex nut assembly in one hand, insert the small hex nut into the top of the smaller diameter chrome plated pole. Turn the pole counter-clockwise to attach both assemblies. Securely tighten the assembly. 8. The floor-mounted Omron Aneroid is now ready for use. On-Site Calibration: 1. Remove the coiled tube from the connector on the underside of the aneroid. 2. Insert the calibration tool (or small flat-head screw driver) into the connector (from where the coi