E/IGLE 602M100R MULTI-FUNCTION STOPWATCH STOPWATCH OPERATING INSTROCTIONS This watch has two modes-TIME and STOPWATCH. Press the [MODE] button to cycle continuously through these modes. TIME MODE To set current date and time of day, press [RESET] button. SECONDS indicator will flash to indicate you are in SET mode. Press [RESET] to cycle through and set each field (SECONDS -> MINUTES -> HOURS -> YEAR -> MONTH -> DAY). Field being set will flash. Press [START] button to set each field. STO

vary with shock, temperature, or aging of crystal). Batteries Batteries should last tor 3 years. If display becomes dim, open back and replace with Duracell D357, Eveready D357, or Ray-O-Vac RW42. ACCUSPLIT, Inc. 3090 Independence Drive, Suite 148 Livermore, CA 94551 USA 800-935-1996 • 925-290-1900 • FAX 925-290-1930 support@ACCUSPLITcom

Whenever the storage is full, extra split/lap times will NOT be stored into memory even though you reset your stopwatch and start a new event. Extra split/lap times will only be shown on the display but not recorded. In order for the stopwatch to record the lap/split times again, you must delete the data in the DATA memory. Please refer to the “Data Mode” section on the instruction manual for how to delete the memory. Instructions Introduction You are about to enjoy an advanced Cumulative and La

Detailed uses of the buttons are different in particular functions and will be described later in the instructions. Pressing [MODE] button will toggle among the modes above. Note that there is no auto-return function in the stopwatch. Whenever you change modes, the stopwatch will remain in that mode until the [MODE] button is pressed again Each time you enter a mode, a message will be displayed for a second before you enter the mode: Note:-In the following descriptions, items printed in dark gra

The timer cycle 12 counter will be increased by one and updated on the display. Under CS operation mode, the timer, after counting down to 0:00'00", will stay at 0:00'00"0 until you press [RESET] to reload the timer value. Under CU operation mode, the timer, after counting down to 0:00'00"0, will count up and stop at 19:59'59"9. How to set the timer Press and hold [RECALL] for 2 seconds to activate timer setting. Timer setting starts with second digits, which are shown blinking. You can press [S

• “Lap time” refers to an elapsed time required to cover a given section of the whole distance. Lap time Split time Start 1. STANDARD MEASUREMENT Hour Seconds Minutes 1/100 seconds START STOP RESET 8 2. ACCUMULATED ELAPSED TIME MEASUREMENT 9 START STOP RESTART RESET STOP Restart and stop of the stopwatch can be repeated by pressing “A”. B A A A 10-11 10 3. SPLIT TIME/LAP TIME MEASUREMENT Note: When the number of stored measurements exceeds 90, fl ashing “FULL” appears, and when it exceeds 100, a

The three dark gray pads must be facing up (away from the case back). c. Finally, put the gasket on top of the gasket holder, and gently push both into the case back until they pop into place. 8. Turn the electronics module over so that the battery is facing the inside of the case back. Gently push the electronics module down into the gray rubber gasket, until it seats. It will be firmly in position if this is done correctly. 9. Slide the button set out of the front case (you'll see that the

The watch uses a high capacity CR2032 Lithium battery, which has an expected life of more than five years in this watch. To change the battery, you will need a set of large jeweler's screwdrivers (including Phillips head). Note: If this looks too complicated, you can always send your watch back to ACCUSPLIT for battery changing instead. See for details. 1. Turn the watch over and select the correct size Phillips screwdriver (the fastening is very tight, so the screws will strip easily if you

To get to this feature, press [MODE] in chronograph mode to enter DATA mode when the stopwatch has been stopped. Records for different segments can be recalled, read or deleted. Detailed operation in "DATA" mode is described in Data Mode section below.. Chronograph Data Recall Mode Press [RECALL] in Chronograph mode to recall stored split/lap time memories. The mode message will be shown up for one to two seconds as mode message display is enabled. RECALL The split and lap time will be displayed

Data Mode (AE760M & AE790M Model only) Press [MODE] until you enter DATA mode The mode message "DATA" will be shown for one to two seconds before the number of free memories is to be shown. FREE 95 LAP You can press [START] to scroll through all segments. The current segment will come first. RECALL {008} 2 0 0 1 SEG {002} 2 - 1 9 A 10: 15' 30 The header consisting of the date/time stamp will be shown. The number of laps in the segment will appear in the upper left while the segment number is dis