Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Телевизоры - 22PFL3504D/F7 (9.66 mb)
Телевизоры - 22PFL3504D/F7 (10.04 mb)
Телевизоры - 22PFL3504D/F7 (8.94 mb)
Фрагмент инструкции
then press OK. Left side Right side 1/5 Select the picture 1/5 Select the picture setting that y1/5 Select the picture setting that yo oo u pref u prefu pref er erer . .. NextOKSelect Back BACK MENU Exit Press OK to finish [Settings assistant]. Settings assistantSettings assistant You have set up your viewing preferences. BackBACKStoreOKExit MENU Finish the Setup. Note • If you connect the cable system directly, contact the CATV installer. • If you press . or MENU during autoprogram, this setting will be canceled. • The initial autoprogram function can be executed for either [Antenna] or [Cable] only once.When you change the connection (Antenna / Cable), set autoprogram again. (Refer to page 21.) • If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the TV, [Helpful Hints] appears. Follow the instructions listed on the TV screen. Settings assistantSettings assistant Settings assistant helps you customizepicture settings. You will see a series of testpictures where the right side and left sidediffer. Select the side that is most pleasing toyou with the Left/ Right keys. BackBACKNextOKExit MENU 10 EN 11 English Switch Channels CHANNEL Press CHANNEL +/- on the side of the TV. For digital channels, press a number (1 to 135) followed by a dot “.” and then the corresponding sub channel number (1 to 135). Ex. 108.30. • Press CH +/- or enter a number on the remote control. • Press PREV CH to return to the previously viewed channel. 5 Use Your TV This section helps you perform basic TV operations. Switch Your TV on/off or to Standby . POWER To switch on • Press . POWER at the side of the TV. • Press . (Standby-On) on the remote control. To switch to standby • Press . (Standby-On) on the remote control. To switch off • Press . POWER at the side of the TV. Note • Energy consumption contributes to air and water pollution. When the AC power cord is plugged in, your TV consumes energy. Your TV has a very low standby power consumption. EN Adjust Volume Still Mode VOLUMETo increase or decrease volume • Press VOL +/-on the remote control or press VOLUME +/-on the side of the TV. To mute or unmute sound • Press MUTE on the remote control to mute the sound. • Press MUTE again to restore the sound. 12 EN You can pause the image shown on the TV screen. Press FREEZE to pause the image shown on the TV screen. FREEZE • The sound output will not be paused. • If no signal is detected or protected signal is received during still mode, the image remains paused and the sound output will be muted. • The still function will be released after 5 minutes. To cancel still mode, press any button except . (Standby-On). Watch Channels from a Set-top Box To watch channels from a set-top box 1 Switch on the set-top box. » The picture from your set-top box might appear automatically on the TV screen. 2 Use the remote control of your set-top box to select channels. If the picture does not appear 12 1 » 2 12 Press SOURCE repeatedly to select the set-top box and wait a few seconds for the picture to appear. Use the remote control of your set-top box to select channels. Watch Connected Devices To watch connected devices Switch on the connected device. The picture from your connected device might appear automatically on the TV screen. Use the remote control of the device to select channels. If the picture does not appear Press SOURCE repeatedly to select the connected device and wait a few seconds for the picture to appear. Use the remote control of the device to select channels. 12 TVWhen only monaural audio is available MONO (cannot be switched) 12 TVWhen only monaural audio is available MONO (cannot be switched) English Watch a DVD To watch a DVD 1 Inser t a DVD disc into your player. 2 Press on the remote control of the DVD player to select channels. » The DVD might automatically play on the TV. If the picture does not appear Press SOURCE repeatedly to select the DVD player and wait a few seconds for the picture to appear. Use the remote control of the DVD player to play the disk. Switching Audio Mode This section describes how to switch the audio in the analog mode and how to switch the audio language in the digital mode. Press SAP to display the currently selected audio mode. While receiving an MTS broadcast, press repeatedly to cycle through the available audio channel. 6 SAP / STEREO When all audio are available SAP / STEREO SAP / MONO SAP / STEREO When stereo and monaural audio are available MONO / STEREO MONO / STEREO When SAP and monaural audio are available SAP / MONO SAP / MONO STEREO : Outputs stereo-audio SAP : Outputs second audio program MONO : Outputs mono-audio DTV 1 Press SAP to display the currently selected language and the number of available languages. 6.1 English 1/3 2 Press SAP repeatedly to cycle through the available audio languages. • Available languages differ depending on the broadcast. [Other] is displayed when the audio language cannot be acquired, or the acquired...
Эта инструкция также подходит к моделям:Телевизоры - 19PFL3504D/F7 (8.87 mb)
Телевизоры - 19PFL3504D/F7E (8.87 mb)
Телевизоры - 19PFL3504D/F7B (8.87 mb)