Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
This picture position movement cannot be controlled by the POS. /SIZE function. • If adjusting the PICTURE V-POS / V-SIZE in Panasonic AUTO with FULL mode, the adjustment is not memorized. When exiting the mode, the screen will return to a former adjustment. AUTO H-POS/V-POS, H-SIZE/V-SIZE, DOT CLOCK and CLOCK PHASE are automatically adjusted when the SETUP RGB or PC signal is received. This setting is enabled under the following conditions: • This setting only support single screen display. Two screen display or multiple display are not supported. • When “COMPONENT/RGB-IN SELECT” or “YUV/RGB-IN SELECT” in the “SET UP” menu (see page 48) is set to “RGB”, this setting is enabled. • When the signal is not PC format, this setting is enabled only if “OVER SCAN” (see page 26) is “OFF” or “1:1 PIXEL MODE” (see page 27) is “ON”, and H-SIZE/V-SIZE is not automatically adjusted. This setting will be invalid and will not work under the following conditions: • Aspect is set to “JUST” • “Display size” in the Options menu (see page 54) is set to “On” Using Remote Control When on the remote control is pressed, “AUTO SETUP” will be executed. When AUTO SETUP does not work, “INVALID” is displayed. Auto mode When the “Auto Setup“ is set to “Auto” in the Options menu (see page 55), automatic position adjustment starts: • When the display power is turned ON. • When the input signal is switched. 1 Press to display the POS. /SIZE menu. 2 Press to select the menu to adjust. 3 Press to adjust the menu. 4 Press to exit from adjust mode. Notes: • Unadjustable items are grayed out. Adjustable items differ depending on the input signal and the display mode. • Adjustment details are memorized separately for different input signal formats. During “VIDEO (S VIDEO)”, “Digital”, “SDI” and “HDMI” input signal. 0 0 0 NORMALNORMALIZE V-POS H-POS 0V-SIZE H-SIZE 1:1 PIXEL MODE OFF AUTO SETUP 0 NORMALNORMALIZE AUTO SETUP POS. /SIZE V-POS 0H-POS V-SIZE DOT CLOCK H-SIZE CLOCK PHASE 1:1 PIXEL MODE OFF 0 0 0 0 Adjusting POS. /SIZE Notes: • If the dot clock frequency is 162 MHz or higher, DOT CLOCK and CLOCK PHASE cannot be made. • When digital RGB signal input, DOT CLOCK and CLOCK PHASE cannot be made. • AUTO SETUP may not work when a cropped or dark image is input. In such case, switch to a bright image with borders and other objects are clearly shown, and then try auto setup again. • Depending on the signal, out of alignment may occur after AUTO SETUP. Carry out fine tuning for the position/size as required. • If AUTO SETUP cannot set properly for vertical frequency 60Hz XGA signal (1024.768@60Hz, 1280.768@60Hz, and 1366.768@60Hz), pre-selecting the individual signal in “XGA MODE” (see page 50) may results in correct AUTO SETUP. • AUTO SETUP does not work well when a signal such as additional information is superimposed out of valid image period or intervals between synchronizing and image signals are short, or for image signal with tri-level synchronizing signal added. • If AUTO SETUP cannot adjust correctly, select “NORMALIZE” once and press ACTION ( ) then adjust POS. /SIZE manually. H-POS Adjust the horizontal position. V-POS Adjust the vertical position. H-SIZE Adjust the horizontal size. V-SIZE Adjust the vertical size. DOT (During “COMPONENT”, “RGB” and “PC” input signal) CLOCK Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, adjust so that any such noise is minimized. CLOCK (During “COMPONENT”, “RGB” and “PC” input signal) PHASE Eliminate the flickering and distortion. OVER Turn image over scan ON/OFF. SCAN Configurable signals are as follows: 525i, 525p, 625i, 625p, 750/60p, 750/50p (Component Video, RGB, DVI, SDI, HDMI) ON OFF Notes: • When “OFF” is set, “H-SIZE” and “V-SIZE” cannot be adjusted. • When the “Display size” is set to “On” in the Options menu, this setting will be invalid. (see page 54) Adjusting POS. /SIZE 1:1 PIXEL MODE Adjusts the display size when 1125i, 1125p or 1250i signal is input. Notes: • Select ON when you would like to replay 1920 . 1080 input signal. • Applicable input signal; 1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p, 1250 (1080) / 50i • Select OFF when flickering is shown around the image. • H-SIZE, V-SIZE and DOT CLOCK cannot be adjusted when ON is selected. OFF ON 1:1 PIXEL MODE (2k1k) (For 2k1k signals) When the input signal is a 2k1k signal (2048.1080 / 24p, 2048.1080 / 24sF), the display size is adjusted as follows. OFF ON (LEFT) ON (CENTER) ON (RIGHT) Note: 2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed. While the POS. /SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings. Helpful Hint ( / NORMALIZE Normalization) PICTURE Adjustments 1 Press to display the PICTURE menu. 2 2 Select to adjust each item. Press to select...