Оценок - 4, средний балл: 4 ( )

Производитель: Hitachi Размер: 2.67 mb Название файла: Язык инструкции:

For example, if you “learned” the A/V receiver’s TV audio input as Input1, select TV Audio from the Assign Input1 column. Likewise, if you “learned” the A/V receiver’s DVD input as Input2, select DVD in the Assign Input2 column. control at the TV and press ENTER to begin learning for Power On. AV Receiver screen. Perform NetCommand IR “learning” for A/V receiver power and volume keys. 3. When the Power On text starts flashing, aim the A/V receiver’s remote control at the TV and press and hold the POWER or POWER ON key until a check mark appears next to Power On. • If the text stops flashing before the check mark appears, repeat this step. • To remove the key from NetCommand control, press the CANCEL key while the key name is highlighted. 58 6. NetCommand IR Control (736 and 835 Series TVs) 6. NetCommand IR Control (736 and 835 Series TVs) 59 1. Under Learn, highlight Input2. Setting Up NetCommand Control of If you have a digital A/V receiver, the TV makes the Setting Up NetCommand Control of audio available by converting analog audio to a In this example, the IR code for the A/V receiver’s an A/V Receiver, continued an A/V Receiver, continued digital output. DVD Audio input will be “learned” as Input2. 4.Press the key on the TV’s remote control to highlight ........................................................ 2. Press ENTER on the TV’s remote control. • Digital Surround Sound: Use Setup 2. other keys in the list. Repeat steps 2 and 3 for each addi- A device can send digital surround sound such as tional function you wish to control through NetCommand. ............................................ ...................................................... ............................................................................ Dolby Digital or DTS directly to the A/V receiver, ........................ .......... 5. If the A/V receiver has a separate POWER OFF key, .................................... bypassing the TV entirely. The device might be ............................................ press on the TV’s remote to highlight Power Off. a DVD player, cable box, or satellite receiver, and .............. Repeat steps 2 and 3 to “learn” the POWER OFF key. could have HDMI output. A DVD player is used in 6. When finished “learning” the power and volume this example. ........................................................................................................................................ keys, either press EXIT to watch TV or leave the AV Your setup may include additional devices with Receiver screen open to continue with NetCom digital surround sound connected directly to the Setup 2: A/V receiver audio from a device providing surround sound directly to the A/V receiver mand setup to control switching of A/V receiver A/V receiver. These devices might be a DVD player inputs. plus a cable box or satellite receiver. ............................................ .............................. A/V Receiver Control: Automatic Audio Switching Perform this setup to enable the A/V receiver to switch automatically to the correct audio input when you select a device in the TV’s Input Selection menu. To set up control of an A/V receiver you need: • The remote controls for both the TV and the A/V receiver. • The IR emitter cable supplied with the TV. Two different setups are described here: Setup 1: Automatic A/V Receiver Switching to TV Audio Input Setup 2: Automatic A/V Receiver Switching for a device sending audio directly to the A/V receiver Review these descriptions to find the setup needed for your equipment. • Audio Available from TV only: Use Setup 1. Audio from ANT 1 and ANT 2 must be sent to the A/V receiver from the TV’s DIGITAL AUDIO OUTPUT or analog AVR AUDIO OUTPUT. Use Setup 1 to make the A/V receiver switch to its designated TV audio input when viewing these sources. • HDMI Digital Stereo Audio: Use Setup 1 Digital stereo audio from an HDMI connection is available both in digital format (from the TV’s DIGITAL AUDIO OUTPUT) jack and in analog format (from the TV’s AVR AUDIO OUTPUT jack). • Analog Stereo Audio: Use Setup 1. Audio from sources with only analog stereo output (such as a VCR) can be sent either directly to the A/V receiver or through to the TV and then on to the A/V receiver. Mitsubishi recommends you send audio through the TV as shown in the example. Setup 1 causes the A/V receiver to switch to its input designated for TV audio. Before You Begin 1. Connect your A/V devices to the TV and connect your A/V receiver to the audio outputs on the TV and the DVD player. See chapter 3, “TV Connections,” for suggestions. Important: You must connect the A/V receiver to the TV’s audio output; use the TV’s AVR AUDIO OUTPUT or DIGITAL AUDIO OUTPUT jack. 2. Position NetCommand IR emitters as described in “IR Emitter Placement,” page 52. 3.Open the Inputs > AV Receiver menu. Note: The terms Input1–Input5 used in the AV Receiver menu are arbitrary names used by the TV to distinguish A/V receiver i...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: