Оценок - 2, средний балл: 5 ( )

Производитель: JVC Размер: 2.67 mb Название файла: Язык инструкции:

The A/V receiver is not switching properly because - you have not learned the inputs. See “Setting Up NetCommand Control of an A/V Receiver,” page 57. 4. There is no sound from the A/V receiver for my DVD player or other surround sound device even though I learned the IR code for the A/V receiver’s DVD input or other input. (A/V Receiver Set Up for Audio-Only Switching) NetCommand A/V receiver setup for the DVD player or digital surround sound device or other device is not switching properly. See chapter 6, “NetCommand IR Control,” and perform A/V receiver setup for a digital surround sound device as described under “A/V Receiver Control: Automatic Audio Switching,” page 58. 5. There is no sound or picture from the A/V receiver for my DVD player or other device connected to the A/V receiver; the A/V receiver should be sending video to the TV over an HDMI cable. (A/V Receiver Set Up for Audio and Video Switching over HDMI) NetCommand A/V receiver setup is not switching audio and video inputs properly. See “Setup to Control Automatic Video and Audio Switching via HDMI,” page 61. 6. I’ve selected my DVD player or other surround sound device in combination with the TV speakers but hear no sound from the TV speakers. A/V Receiver Set Up for Audio-Only Switching • If you have only an audio connection from the device to the A/V receiver, a physical audio connection from the device to the TV is also required. Connect the left and right audio output from the device - to the appropriate TV audio input. Now you can hear audio from the device through either the TV speakers or the A/V receiver. To switch audio sources, press AUDIO, press -to show the Speakers option, then press to select AV Receiver or TV. A/V Receiver Set Up for Audio and Video Switching over HDMI • With your DVD player connected to the A/V receiver, only video is passed from the A/V receiver to the TV because of copy-protection restrictions on the HDMI signal 7. I “learned” the RECORD key for my VCR/DVR but when I pressed the RECORD key, the VCR/DVR did not record anything. Check that the VCR or DVR is receiving a signal directly from your cable box or satellite receiver. Appendices Appendix E: Lamp-Cartridge Replacement and Cleaning Appendix E: Lamp-Cartridge Replacement and Cleaning WARNING THE ACCESS PANEL IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING PANEL COMPLETELY. CAUTION BURN DANGER! HOT SURFACES INSIDE! Touch lamp cartridge handle only. Do not touch lamp or lamp cartridge housing. Keep lamp cartridge horizontal during removal. Do not tilt as glass may come out and cause injury. Replace lamp cartridge only with the same part number 915B403001. CAUTION: If the television is on, press POWER to turn it off. Unplug the television and allow it to cool for at least one hour before attempting to replace the lamp cartridge. Lamp Life The light source for this television is a lamp, which is part of a lamp cartridge assembly. The life of the lamp can vary, based on the lamp itself, the air temperature around the TV while it is operating, the selected lamp mode, and your viewing patterns. Warmer air or poor ventilation shorten the lamp life, as does use of the Bright lamp mode and turning the television on and off frequently. Mitsubishi warrants the lamp for one (1) year from the date of original purchase at retail. It is likely that the lamp will last much longer than this. To Order a New Lamp To Receive a Replacement Lamp Under Warranty Call (800) 553-7278. Please have model number, serial number, and TV purchase date available. Important: All lamps replaced under warranty must be returned to Mitsubishi where they will be inspected for defect verification. To Purchase a Replacement Lamp After Warranty Visit our website at or call (800) 553-7278. Order the following: Lamp Part Number 915B403001 WARNING • Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the lamp is very hot. Allow the television to cool for at least one hour before replacing the lamp cartridge. • Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire. • Do not touch the lamp glass element. It may be very hot and break, causing injuries or burns. • Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical shock. If a foreign object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for service. • Install the lamp cartridge securely. Failure to do so may cause a fire. • Do not touch the lamp glass elements. Oils from your fingers may cause premature lamp failure. Hg THE LAMP INSIDE THIS PRODUCT CONTAINS MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. For disposal or recy = MERCURY cling information, please contact your local autho...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: