Оценок - 2, средний балл: 4
(
)
)
|
Фото и характеристики Clarion VMA7196 |
Фрагмент инструкции
When replacing a fuse, never let the battery side touch any metal part or any other wire. WARNING! Be sure to disconnect the battery (-) terminal before starting. This is to prevent short circuits during installation. Car battery Procedure 1. Disconnect the negative (-) lead from the vehicle’s battery. 2. Find a place in the vehicle for the video source(s). 3. Create passage holes for the power and video cables. When drilling through metal or plastic, use grommets to protect the cables from sharp edges that could penetrate the insulation and cause a short circuit and device failure. 4. Connect the ground lead (black) securely to a clean metal plate on the vehicle. Use sand paper to remove any paint from the surface where you attach the ground terminal. 5. Reconnect the negative (-) lead to the battery. VMA5096/VMA7196 15 English VMA5096_VMA7196_OwnersManual_rev.pmd.p65 15 11/23/05, 2:54 PM English Monitor connections CAUTION! Some non-Clarion automotive DVD and VCP source units use a similar connector for an external IR receiver, but use different pin polarity than the Clarion uses. Connecting non-Clarion source equipment to this connector could cause equipment damage not covered by the warranty! IR connector polarity +5V ACC Ground IR Data Line Connections diagram R W Y R W Y 3 Audio R 8 12V 4 Video GND 9 GND or 1 Audio L 6 12V GND 2 IR GND 7 IR Y - Video RCA Input W - Audio (L) Input 5 Video R - Audio (R) Input 16 VMA5096/VMA7196 VMA5096_VMA7196_OwnersManual_rev.pmd.p65 16 11/23/05, 2:54 PM 7. Troubleshooting The monitor does not turn on A fuse may be blown. Replace the external fuse with a fuse of the same value. The power wires may not be connected. Check the wiring connections and retest. No picture. Press INPUT to make sure the proper input is selected. If there is still no picture, press MENU. If the menu appears, check the source unit and video connections. If no menu appears, check all fuses and power connections to the monitor and the associated equipment. Note: The monitor has an operating temperature range of -1o C to 45o C (30o F - 113o F). If the temperature is outside this operating range, the unit will not turn on, or the screen may be slow to react to image changes. The monitor will function normally once it returns to its proper operating range. There are black bars above and below the picture with widescreen DVD disc Change the monitor display mode from “Full” to “Wide.” Access DVD player’s Setup menu. After changing this setting, if there are still black bars, press WIDE on the front panel of the monitor and select WIDE. The screen is dark The brightness is set too low. Press MENU and adjust the BRIGHT option. The interior of the vehicle is too hot or too cold. The monitor’s operating temperature is 1 degree to 45 degrees Celsius (30 degrees to 113 degrees Fahrenheit). Picture “rolls” or appears B/W Check that the VIDEOSYS setting is correct for the monitors and DVDs being used (see “Changing the Video Output Mode”). PAL video often “rolls” on NTSC monitors. VMA5096/VMA7196 17 English VMA5096_VMA7196_OwnersManual_rev.pmd.p65 17 11/23/05, 2:54 PM 8. Specifications Note The technical data and the design of the equipment may change without prior notice for the sake of technical improvements. VMA5096 General Specifications Power requirement: 12V DC (9V-16V) Power consumpaion: 6.5 watts, power on 0.6 amps (600mA) Weight: 300 g Dimensions (w x h x d): 138 x 106 x 26.5 mm Included parts: LCD monitor 1 - 16P Main cable 1 - Mounting bracket Monitor release tool VMA5096 Monitor Specifications Display type: Color TFT Active Matrix LCD Screen size: 5” Pixels: 960 x 220 Screen resolution 211,200 dots Video input level (RCA) 1.0 volts peak to peak, NTSC VMA7196 General Specifications Power requirement: 12V DC (9V-16V) Power consumpaion: 6.5 watts, power on 0.6 amps (600mA) Weight: 345 g Dimensions (w x h x d): 183.2 x 128 x 29 mm Included parts: LCD monitor 1 - 16P Main cable 1 - Mounting bracket Monitor release tool VMA7196 Monitor Specifications Display type: Color TFT Active Matrix LCD Screen size: 7” Pixels: 1440 x 234 Screen resolution 336,960 dots Video input level (RCA) 1.0 volts peak to peak, NTSC 18 VMA5096/VMA7196 VMA5096_VMA7196_OwnersManual_rev.pmd.p65 18 11/23/05, 2:54 PM 9. LIMITED WARRANTY INFORMATION For USA and Canada only Except as noted, Clarion products purchased from an authorized Clarion dealer are warranted against all defects in materials and workmanship for a period of one (1) year from date of original purchase. The following Clarion products noted below ** are warranted against all defects in materials and workmanship for a two (2) year perod from the date of original purchase when purchased from AND installed by an authorized Clarion dealer. ** DRZ9255 DXZ865MP DXZ765MP DXZ665MP DXZ465MP DFZ675MC DPX1150 DPX1800 DPX2250 All Clarion cables, wires and other accessories if purchased from an authorized Clarion dealer are warranted against all defects in materials and workmanshi...
Эта инструкция также подходит к моделям:Телевизоры - VMA5096 (590.71 kb)