To avoid restricting the outlet, maintain a minimum of 12 inches (30.5 cm) clearance between the vent hood and the ground or any other obstruction. The vent flap should be able to move freely. MAXIMUM EXHAUST LENGTH 14 GDZ22-1 manual 10/22/01 11:45 AM Page 16 English After installation is completed, the following method must be used to determine if the exhaust system is acceptable: 1. Connect an inclined or digital manometer between the dryer and the point the exhaust connects to the dryer. 2. S

During the operation, with the variation of the factors such as the moisture content the actual remaining time program will be automatically adjusted until the preset drying result has been achieved and the program is complete. G -Indicator light for cleaning up the condensate collection box When this light is on, it indicates that the condensate collection box is full of condensate. Please empty the box. At this time the operation of the program will be halted. After the box is emptied, press t

Select 'Softon the heatselector button and set thedrying timer knob between 30- 60 minutes depending on thequantity of items in the dryer. When the timer stops after the Cool program, the items will stillcontain moisture. This willmake the ironing easier. ' Warm: This function will dry and coolitems and in most cases leave items wrinkle free (depending on material). Select the 'Strong heat option and setthe timer between 60-150 minutes. ' OFFOFFAir dryCool0060402022020018016014012010080604020Dry

The thickness ,size , type of the cloth will influence the actual spinning time. Using sequence Please make the machine stand horizontally. Confirm that the washing machine is earthed reliably . Then insert the power plug I nto the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. Put down the drain hose . Preparation before spinning Spin process 1 Put the laundyies in properly 2 Put the gland in properly 3 Close the inner and outer coverof the spin tub 4 Do you n

Drying Rack (some models) lint screen opening. 4. 5. damage to the dryer. Common Drying Problems Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association. PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES Greasy, oily • Fabric softener sheet. • Rub fabric softener stains with bar soap. • Add a few bath towels to small l

For Warranty Service Contact your nearest authorized service center. All service must be performed by a Haier authorized service center. For the name and telephone number of the nearest authorized service center please call 1-877-337-3639. Before calling please have available the following information: Model number and serial number of your appliance( found on the rear of the unit on the upper left hand side). The name and address of the dealer you purchased the unit from and the date of purchas

Good safe practice and caution must be applied when installing, operating and maintaining any appliances, after installing, if you are in doubt, call a certified electrician to install and wire the dryer. 12 English OPERATING INSTRUCTIONS Understanding the Control Panel Note: Features may vary per model. Start/Pause Button: (1) • Press the button to turn the dryer ON. Press this button once to start the dry process. Press this button once again to pause the activity during the dry cycle. Off But

Any floor unevenness should be corrected with leveling legs located on the bottom of the dryer. Tools and materials required • Phillips head and flathead screwdrivers • Channel-lock adjustable pilers • 1/2 inch open end wrench • Carpenter’s level • Measuring tape (12ft. min.) • Duct tap • Rigid or flexible metal 4 inch (102cm) duct • Vent hood Electrical requirements U.S. Only Power supply: 3 or 4 wire, 240 Volt, 30 Amp,60Hz, 1 Phase Power Supply Cord Kit (not supplied when sold in the United St

Press "Start/Pause" button or after half a minute, the program defined by user himself will be stored and will be directly displayed upon next use. Notes: Pressing "Sensor Dry Level" button will be inactive during use of "Custom" function. 3. Press "Sensor Dry Level" button to select a suitable drying time. • After powering on, the clothes dryer automatically sets dryness at "very", which means a longer drying time. If other drying time is desired, press "Sensor Dry Level" button to select a sho

Press "Wrinkle Care" button to select wrinkle-proof drying mode Wrinkle Care automatically sets "Off" upon powering on. Press "Wrinkle Care" button, it sets wrinkle Care drying mode. Notes: "Wrinkle Care" function is provided to match "Delay Start" program. When a "Delay Start" drying cycle ends, clothes remained in hot drum is prone to creasing. "Wrinkle Care" function operates in tumbling clothes by intermittently rotating drum to avoid clothes wrinkling. 8. Press "Start/Pause" button If start