Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Place washer firmly on a stable, even and solid floor. Peel protective paper off the tape from the stacking kit side bracket. Fit the stacking kit side bracket firmly to the side of top plate by attaching the doublesided tape to top plate as picture shows. Secure stacking kit side bracket to the washer with a screw on the back of bracket. Repeat Steps 2, 3, 4 for the other side. Place the dryer on top of the washer by fitting legs as shown in the picture. Avoid finger injuries - be careful not to pinch fingers between the washer and dryer. Slide dryer slowly backwards to the stopper of kit. Insert the front rail. Push the front rail back to the stoppers of side stacking kit. Attach both sides of the front kit with screws. • Do not use stacking kit with a gas dryer in potentially unstable conditions like a mobile home. Stacking kit 12 3 4 5 6 7 Stacking Kit Installation Instructions Clean the surface before attaching the brackets and double-sided tape. ! WARNING! Note • The weight of the dryer and the height of installation makes the stacking procedure too risky for one person. This procedure should be performed by 2 or more experienced service personnel. • Incorrect installation can cause serious accidents. ! WARNING! • Do not stack a washer on the top of the dryer. • Incorrect installation can cause serious accidents. Dryer Washer Part 4 16 ACCESSORIES INSTALLATION Pedestal Installation Instructions for washer/ combo for dryer for washer/ combo for dryer 3 1 4 5 6 7 2 1) Shut off gas. 2) Unplug power cord. 3) Disconnect gas line from dryer. 4) Pull away and loosen vent clamp. 5) Disconnect venting. Part 5 ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS The following are additional instructions regarding electrical connections and requirements for electric dryers. ! Warning: The wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer. Failure to do so can result in fire or electrical shock. 120V/ 240V, 60 Hertz, 3-Wire Installation Instructions for Grounding of your Electric Dryer: a) This dryer must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. b) The dryer has its own terminal block that must be connected to a separate 60 Hertz single phase AC circuit, fused at 30 Amperes (the circuit must be fused on both sides of the line). ELECTRICAL SERVICE FOR THE DRYER SHOULD BE OF MAXIMUM RATE VOLTAGE LISTED ON THE NAMEPLATE. DO NOT CONNECT DRYER TO 110, 115, OR 120 VOLT CIRCUIT. Heating elements are available for field installation in dryers which are to be connected to electrical service of different voltage than that listed on nameplate. c) If branch circuit to dryer is fifteen feet (4.50 m) or less in length, use U.L. (Underwriters Laboratories) listed No. 10 A.W.G. wire (copper wire only), or as required by local codes. If over fifteen feet (4.50 m), use U.L. (Underwriters Laboratories) listed No. 8 A.W.G. wire (copper wire only), or as required by local codes. Allow sufficient slack in wiring so dryer can be moved from its normal location when necessary. d) The power cord (pigtail) connection between wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions mentioned on the following pages. e) The method of wiring the dryer is optional and subject to local code requirements. Refer to examples on next page. f) You must select the method by which to wire your dryer according to local code and ordinance requirements. Sample methods are included in the following pages. 18 Part 5 ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS Use the instructions in this section if your home has a 3-wire receptacle (NEMA type 10-30R) and you will be using a UL listed, 120/240 volt minimum, 30 amp, dryer power supply cord. Review the following options to determine the appropriate electrical connection for your home: If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker box. Warning : Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. Failure to do so can result in fire or electrical shock. Prepare minimum 5 ft (1.52 m) of length in order for dryer to be replaced. First, peel 5 inches (12.7 cm) of covering material from end. Strip 5 inches of ground wire insulation. After cutting 11/2 inch (3.8 cm) from 3 other wires peel insulation back 1 inch (2.5 cm). Make ends of 3 wires a hook shape. Then, put the hooked shape end of the wire under th...