Do not operate the mower without either the discharge chute or the entire grass collection system in place. Fig. 3-12 600876_0706 15 600876_0706 Mower deck operation DANGER: Never attempt to make any adjustments to the mower deck while the engine is running or with the deck drive clutch engaged. Mower blades cannot be seen and are located very close to deck housing. Fingers and toes can be cut off instantly. With the engine running, engage the deck clutch switch (Fig. 3-1) and advance engine thr

Change hydraulic system filter element after first 50 hours of tractor operation, then replace filter and oil in reservoir every 500 hours thereafter. When changing hydraulic oil use 1/2 unit (approximately 3.5 oz.) of Lubrizol additive (Hustler P/N 027912). This additive, available from your Hustler dealer, will increase the performance life of the hydraulic system components. The system filter is located to the right of the hydraulic reservoir. A 600876_0706 20 standard oil filter wrench is us

An operator should not operate on a slope until he is thoroughly familiar with the equipment. Do not operate on slopes greater than 15 degrees. Refer to Figure 2-1, page 7, when determining the degree of slope to be mowed. IMPORTANT: The Hustler ATZ only, is capable of operating on slopes of 15 degrees or more (maximum 25 degrees). Do not operate the Hustler ATZ on slopes greater than 25 degrees. Refer to Figure 2-1, page 7 when determining the degree of slope to be mowed. It is strongly recomme

Change more often under dusty or dirty conditions and during hot weather periods. 2. Torque initially and after first 2 hours of operation. 3. Perform initial hydraulic filter change after 50 hours (one week) of operation. 4. Change engine oil filter per the engine manufacturer’s recommendations. Refer to Engine Owner’s Manual for recommendations and other maintenance items. 5. Service more often under dusty or dirty conditions. Use caution when servicing to prevent dust contamination in the eng

C. Deck clutch switch (Fig. 3-1) — this switch engages the deck. Pull the switch up to engage and push switch down to disengage the clutch. IMPORTANT: Never engage clutch with engine running at high rpm or when the deck is under load. Clutch, belts or deck could be damaged. D. Ignition switch (Fig. 3-1) – a three position switch: off, run, and start. With key inserted, rotate it clockwise to START position; release key when engine starts, and switch will automatically return to the RUN position.

Do not overfill battery. Electrolyte may overflow and damage paint, wiring or structure. When cleaning the battery, use soap and water. Be careful not to get soap and water into the battery. Use soda mixed in water to clean corrosion off the terminals. Avoid crushing Do not jump if machine tips Use seat belt Seat belt must be fastened while operating this machine. Failure to use seat belt will result in serious injury in the event of a roll over. Keep engine and pump compart-ment(s) clean (espec

Maintain and store your power chair in a dry and clean condition. WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of upholstered and non-upholstered items on the power chair, possibly resulting in skin irritation. Exercise caution when using your power chair in extremely hot or cold conditions or when exposing your power chair to direct sunlight for prolonged periods of time. Stationary Obstacles (Steps, Curbs, etc.) Proceed with extreme caution when driving near

BLACK (-) cables must be connected to negative (-) battery terminals/posts. Protective caps should be installed over all battery terminals. REPLACE cables immediately if damaged. I I . S A F E T Y II. SAFETY Prescription Drugs/Physical Limitations Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations. WARNING! Consult your physician if you

Temperature • Some of the parts of your power chair are susceptible to extreme changes in temperature. Always keep your power chair between the temperatures of 18°F (-8°C) and 122°F (50°C). • In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a number of factors, such as battery charge, usage, and composition of the batteries (e.g., AGM or Gel-Cell). • Temperatures above 122°F (50°C) may cause your power chair to operate at a reduced

Your Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements. Do not change your seating configuration without first contacting Pride Mobility Products or your Quantum Rehab Provider. WARNING! Some power chair components are heavy. You may need assistance to lift or carry them. Please refer to “Appendix I - Specifications” for specific component weights before you disassemble the power chair. WARNING! Remove the occupant from th