Оценок - 4, средний балл: 4.5 ( )

Производитель: Hustler Turf Размер: 9.47 mb Название файла: Язык инструкции:

Do not operate the mower without either the discharge chute or the entire grass collection system in place. Fig. 3-12 600876_0706 15 600876_0706 Mower deck operation DANGER: Never attempt to make any adjustments to the mower deck while the engine is running or with the deck drive clutch engaged. Mower blades cannot be seen and are located very close to deck housing. Fingers and toes can be cut off instantly. With the engine running, engage the deck clutch switch (Fig. 3-1) and advance engine throttle to full rpm. NOTE: Engaging the deck clutch at high engine rpm or when under heavy load (in tall grass for example) can cause belts and/or electric clutch to slip, resulting in premature wear or possible damage. Deck cutting height adjustment Hustler Mini Z/Super Mini Z Deck height is adjustable from 1-1/2” to 4-1/2” (3.81 cm - 11.43 cm) in 1/4” increments. The holes in the height adjusting bar are spaced at 1/2” intervals. By turning the height adjusting stop around, 1/4” increments can be attained due to the 1/4” plate that is part of the stop. Fig. 3-13 EXAMPLE: When the height adjusting stop is placed in the 1-1/2” hole, with the 1/4” plate facing to the front of the unit, the cutting height is at 1-1/2”. When the height adjusting stop is placed in the 1-1/2” hole, with the 1/4” plate on the operator’s side of the hole, the cutting height is at 1-3/4”. The notch located at the rear of the height adjusting bar is to be used when the deck is placed in the transport mode. Hustler Z/Super Z/Hustler ATZ Deck height is adjustable from 1” to 5” (2.54 CM - 12.7 CM) in 1/4” (.64 CM) increments. The holes in the height adjusting bar are spaced at 1/2” (1.27 CM) intervals. By turning the height adjusting stop around, 1/4” (.64 CM) increments can be attained due to the 1/4” (.64 CM) plate that is part of the stop. Fig. 3-13 EXAMPLE: When the height adjusting stop is placed in the 1” (2.54 CM) hole, with the 1/4” (.64 CM) plate facing to the front of the unit, the cutting height is at 1”. When the height adjusting stop is placed in the 1” (2.54 CM) hole, with the 1/4” (.64 CM) plate on the operator’s side of the hole, the cutting height is at 1-1/4” (3.18 CM). The notch located at the rear of the height adjusting bar is to be used when the deck is placed in the transport mode. Super Z Diesel Deck height is adjustable from 1” to 7” (2.54 CM - 17.78 CM) in 1/4” (.64 CM) increments. The holes in the height adjusting bar are spaced at 1/2” (1.27 CM) intervals. By turning the height adjusting stop around, 1/4” (.64 CM) increments can be attained due to the 1/4” (.64 CM) plate that is part of the stop. Fig. 3-13 There are three (3) holes in each of the four (4) deck chain brackets that are also used for height adjustment. Fig. 3-14 The top hole is used for cutting heights of 1” - 5” (2.54 - 12.70 CM). The following information is to ascertain what to set the cutting height at when the top hole is used. Figure 3-12 Side discharge chute Neutral Left control lever Left control lever Right control lever Three point turn Step 1 Step 2 Step 3 Right control lever Neutral Neutral Right control lever Left control lever Figure 3-11 16 Height adjusting stop Stop handle Figure 3-13 When the chains are placed in the top hole of the deck chain brackets and the height adjusting stop is placed in the front height adjusting bar hole, with the 1/4” (.64 CM) plate facing to the front of the unit, the cutting height is at 1” (2.54 CM). When the height adjusting stop is placed in the same hole, with the 1/4” (.64 CM) plate on the operator’s side of the hole, the cutting height is at 1-1/4” (3.18 CM). The middle hole is used for cutting heights of 2” - 6” (5.08 CM 15.24 CM). The following information is to ascertain what to set the cutting height at when the middle hole is used. When the chains are placed in the middle hole of the deck chain brackets and the height adjusting stop is placed in the front height adjusting bar hole, with the 1/4” (.64 CM) plate facing to the front of the unit, the cutting height is at 2” (5.08 CM). When the height adjusting stop is placed in the same hole, with the 1/4” (.64 CM) plate on the operator’s side of the hole, the cutting height is at 2-1/4” (5.72 CM). The lower hole is used for cutting heights of 3” - 7” (7.62 CM - 17.78 CM). The following information is to ascertain what to set the cutting height at when the lower hole is used. When the chains are placed in the lower hole of the deck chain brackets and the height adjusting stop is placed in the front height adjusting bar hole, with the 1/4” (.64 CM) plate facing to the front of the unit, the cutting height is at 3” (7.62 CM). When the height adjusting stop is placed in the same hole, with the 1/4” (.64 CM) plate on the operator’s side of the hole, the cutting height is at 3-1/4” (8.26 CM). The notch located at the rear of the height adjusting bar is to be used when the deck is placed in the transport mode. Anti-scalp wheels Anti-scalp wheel kits are standa...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: