Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Store these products out of the reach of children. p . Always take into account the instructions on the labels of clothes. Never allow children to play in the surroundings of a machine. p p Remark: These instructions surely cannot prevent all risks of accidents. It is up to the user to act with the utmost precaution. Do not hesitate to contact the dealer in case of a problem. 3 Technical data and dimensions Technical data HF 455 HF 575 Capacity (dry weight) 1/11 40,9 kg 51,8 kg 1/10 45 kg 57 kg 1/9 50 kg 63,3 kg Cylinder Diameter 980 mm 980 mm Depth 597 mm 775 mm Volume 450 Lit. 570 Lit. Cabinet Height 1950 mm 1950 mm Width 1200 mm 1200 mm Depth 1190 mm 1405 mm Front loading Diameter door opening 395 mm Door height - lower edge 800 mm Door height - center 1000 mm Speed Wash 10--50 tr/min. Distribution 100 tr/min. Spin 250--400 tr/min. High spin 500--800 tr/min. G-force Spin High spin 87 350 Motors (3-phase) 4p. 1470 rpm 7500W Drain Depend-O-Drain 3 Water-inlet Hard, soft, hot water 3/4" Steam connection Steam connection 1/2" Heating Electric 220/380 V Electric 380 V Steam Boiler fed Boiler fed (with auxiliary heating) 27 kW 36 kW X X X Packing dimensions (H x W x D) With liquid soap pumps 2100x1350x1430 2100x1550x1430 2100x1350x1630 2100x1350x1630 Weight Net Gross 1000 kg 1200 kg 1100 kg 1300 kg 4 Afmetingen 455 ppp . pppp A. Soft water connection 3/4" B. Warm water connection 3/4" C. Hard water connection 3/4" D. Electrical connection E. Electrical connection soap pumps F. Main switch G. Ventilation tub H. Connection of the liquid soap hoses I. Steam connection 1/2" J. Water drain p . 5 Dimensions Dimensions ppp . pppp A. Soft water connection 3/4" B. Warm water connection 3/4" C. Hard water connection 3/4" D. Electrical connection E. Electrical connection soap pumps F. Main switch G. Ventilation tub H. Connection of the liquid soap hoses I. Steam connection 1/2" J. Water drain p . 6 Installation and connection Ground The machine must be placed on a flat, solid surface (metal base, concrete or solid ground). It isrecommended that the machine be anchored (M16) on the provided places (A) in the base, especially in case of a plinth (see Dimensions 2). The machine must be placed entirely level. For easy maintenance it is recommended to keep a minimal distance of 600 mm between the wall and the back of the machine. If several machines are placed next to each another, there should be a minimal distance of 30 mm between each machine. Removing the transport brackets To prevent damage during transportation, the machine has been equipped with four red transport brackets (D) to eliminate every possible movement of the tub. After the machine has been placed level, take off the service- and the back panel to remove these transport brackets. Important The machine must never be activated before removing these transport brackets. Water connection The machine is delivered with hoses with 3/4" connections. These hoses fit the water inlet valves of the machine and the main water inlet taps. To ensure the optimal functioning of the water inlet valves, the water pressure on the inlet should be between 0,5 and 10 kg/cm. (7 and 145 psi). If the pressure is too low, the cycle time will increase considerably. In case of boiler fed machines, a minimum of hot water of 90°C should be available: For the HFP455: 350 l. HFP575: 445l. 7 Water drain The machine is equipped with a drain valve with 3" outer diameter (80 mm). This drain valve should be connected to the drain by means of the drain elbow which is delivered with the machine. pThe diameter of the main drain should be adapted to the water flow and the number of machines. It should be sufficient to handle at least 160L/ min. per machine. pIt is necessary to connect the main drain at least on one side to an open air-brake to allow ventilation. pWhen the main drain has not been sufficiently deodorized, every machine should be installed seperately with a deodorizer. Electrical Connection pRemove the cover plate at the back of the machine (see dimensions). pConnect the power cable to the connectors R,S,T (3 x 220V) or R,S,T and N (3 x 380V + N) and the ground wire. Machine without electrical heating Power of the breaker plugs: 220V 3AC 380V 3AC + N 20 A 20 A Machine with electrical heating Power of the breaker plugs: 220V 3AC 380V 3AC + N 27 kW 80 A 63 A 36 kW ----80 A After having connected the machine, check the spin direction of the drum. The drum should spin in the direction of the arrow indicated on the door glass (clockwise). If the drum spins in the wrong sense, it can cause damage to the motor and can cause water to splash out through the soap dispenser. In case of a wrong spin direction, switch the position of the connectors of the motor circuit from R to S and vice versa. 8 Automatic lubricator The bearing house of the machine is equipped with a lubricating device (A) which automatically lubricates the bearing during one year. Upon delivery of the machine, this lubricator ha...
Эта инструкция также подходит к моделям:Стиральные машины - HF575 (265.25 kb)