Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
6752134 Re f e r e nc e G r ounding c o mpone nt 1 Electric service equipment 2 Power service grounding electrode system (NEC Art 250, Part H) 3 Ground clamp 4 Grounding conductors (NEC Section 810-21) 5 Antenna discharge unit (NEC Section 810-20) 6 Ground clamp 7 Antenna lead-in wire • Use No. 10AWG (5.3 mm2) copper, No. 8AWG (8.4 mm2) aluminum, No. 17AWG (1.0 mm2) copper-clad steel or bronze wire, or larger, as a ground wire. • Secure the antenna lead-in and ground wires to the house with stand-off insulators spaced from 4-6 feet (1.22-1.83 meter) apart. • Mount the antenna discharge unit as close as possible to where the lead-in enters the house. • Use a jumper wire not smaller than No. 6AWG (13.3 mm2) copper, or the equivalent, when a separate antenna-grounding electrode is used. See ANSI/NFPA70. • For added protection for your television during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the power outlet and disconnect it from the antenna or cable system. This prevents damage to your television due to lightning and power line surges. • An outside antenna system should not be located in the vicinity of overhead power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. • Do not overload power outlets and extension cords because overloading can cause a fire or electric shock. • Never push objects of any kind into your television through slots in the case because they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on your television. • Do not attempt to service your television yourself because opening or removing covers may expose you to dangerous voltages or other hazards. Refer all servicing to qualified service technicians. • Unplug your television from the power outlet and refer servicing to qualified service technicians under the following conditions: • When the power cord or plug is damaged or frayed. • If liquid has been spilled into your television. • If your television has been exposed to rain or water. • If your television does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions because incorrect adjustment of other controls may result in damage and often requires extensive work by a qualified technician to restore normal operation. • If your television has been dropped or the case has been damaged. • When your television exhibits a distinct change in performance. • When replacement parts are required, make sure that the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. • Upon completion of any service or repairs to your television, ask the service technician to perform routine safety checks to determine that your television is safe to operate. Note to cable television system installer This reminder is provided to call the cable television system installer’s attention to Section 820 40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Insignia NS-F20TV Television Features Back Television Front 1 2 34 5 6 7 89 Item Description 1 Power button—Press to turn the television on or off. 2 Remote sensor—Point the remote control at this sensor to control the television. 3 Indicator—Glows green when the power is turned on. 4 INPUT button—Press to select the input source. 5 MENU button—Press to access the on-screen menu. 6 VOL-button—Press to adjust the volume down or to adjust a menu item. 7 VOL+ button—Press to adjust the volume up or to adjust amenu item. 8 CH-button—Press to adjust the channel down or to selecta menu item. 9 CH+ button—Press to adjust the channel up or to select a menu item. 7 6 5 4 2 1 3 Item Description 1 AV2 input (VIDEO, AUDIO L, AUDIO R)—Connect a video and audio source, such as a camcorder, video gameconsole, or DVD player, using these jacks. 2 Headphone jack—Connect a headphone to this jack. 3 Antenna input—Connect cable or satellite television, an outside antenna, or rabbit ears to this jack. 4 COMPONENT input (Y, CB, CR, AUDIO L, AUDIO R)— Connect a video and audio source, such as a DVD player, using these jacks. Component video provides the highestquality picture. 5 S-VIDEO input—Connect a video source using this jack. Audio is not transmitted through the S-VIDEO cable. 6 AV1 input (VIDEO, AUDIO L, AUDIO R)—Connect a video and audio source, such as a video game console or DVDplayer, using these jacks. 7 AV output (VIDEO, AUDIO L, AUDI...