3. Move the point of skew to the right half of the desired width of your cut, see Figure 19. 4. With the bevel parallel to the right side of the cut, raise the handle and push the tool in to the desired depth. 5. Repeat from the left side. The two cuts should meet at the bottom and leave a clean "V" cut. 6. Additional cuts may be taken to add to either the depth or width of the cut. Parting 1. Place the parting tool on the tool rest and raise the handle until it starts to cut and continue to cut

1 29........ JWL1642-129 ...............Plate...................................................... ............................................... 1 ........JWL1642-130...............Digital Readout......................................JWL-1642EVS........................1 ............JWL1642-130A.............Digital Readout......................................JWL-1642EVS-2.....................1 31........ TS-1540011..................Nut ........................................................

If in doubt, use the next heavier gauge. Remember, the smaller the gauge number, the heavier the cord. Volts Total Length of Cord in Feet 120V 25 50 100 150 AWG 12-16 Amps 14 12 Not Recommended 5 230 Volt Operation If 230V, single-phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This lathe is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 2

5-6 6-7 Nomenclature and Use """'..". 7 Adjusting Tool Rest Operation Parts Breakdown ... ... ... 7 8-11 12 Parts List 13-14 Electrical Schematic ...... .15 3 Uncrating and Clean-Up Note: Uncrating and assembly will require two people due to the machines size and weight. 1. Finish removing contents from the shipping crate. Be sure to check crate thoroughly for any parts not found on initial unpacking. 2. Inspect contents for shipping damage and report any damage to your distributor. 3. Clean all

Now, the new JET JWL-1220VS lathe brings variable speed to this instantly popular machine. Add the JWL1220BE 28” bed extension and the JET JWL-1220VS 50” between centers capacity rivals that of many larger, more expensive lathes. The JET JWL-1220VS lathes are built using our time honored heavy cast iron technology to insure maximum accuracy and the long-term durability that makes the JET JWL-1220VS Wood Lathe an even greater value. Power and Speeds Pulley Position The JET JWL-1220VS lathe featur

To order parts or reach our service department, call 1-800-274-6848 between 7:30 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Figure 13 12 JML-1014I Mini Lathe 13 Parts List for JML-1014I Mini Lathe Index No. Part No. Description Size Qty 1............. JML1014-101 .... .....Headstock................................................. ..... 1 2..........

8 Installing Pen Mandrel Screw the mandrel (A, Fig. 10) into the threads in the headstock spindle and place the other end on the tip of the live center of the tailstock as shown. The barrel(s) of a pen can be placed between bushings, and held snug on the mandrel by the knurled nut (B, Fig. 10). If you are new to the practice of pen turning, a book entitled “Pens from the Wood Lathe” (stock # 709123) will demonstrate techniques and tips on turning, and is available from WMH Tool Group. Complete s

This new 3/4HP lathe supports stock up to 12" in diameter and 20" in length. A built-in work light illuminates your work piece while turning and the spindle has a lock and indexing capability for fluting and veining applications. Integrated carry handles and a cord wrap are added for portability. STOCK NO. 900493 10M 07/07 ©2 0 07 WMH TOOL GROUP, Inc. All Rights Reserved. Jettools.com JWL-1220: 12"x20" WOOD LATHE STOCK NUMBER 708376 Model Number JWL-1220 • Heavy-duty cast-iron lathe

This ^ HP lathe supports stock up to 10" in diameter and 14" in length. This lathe features solid cast iron construction, the added convenience of a hollow tailstock, a 6" tool rest and electronic variable speed. The spindle also has a versatile locking/indexing mechanism for fluting and veining applications. rri JET 10"x14" VARIABLE SPEED INDEXING MINI LATHE 10"x14" VARIABLE SPEED INDEXING MINI LATHE • continously variable speed operation from 500-3900 rpm • Heavy-duty cast-iron lathe bed

M-708376 Ph.: 800-274-6848 Revision A 9/06 Copyright © WMH Tool Group WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. Fo