Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Walk, never run. 14. Disengage power to the auger/impeller when transporting or not in use. 15. Never operate machine at high transport speeds on slippery surfaces. Look down and behind and use care when in reverse. 16. If the machine should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and ground it against the engine. Inspect thoroughly for damage. Repair any damage before starting and operating. 17. Disengage all clutch levers and stop engine before you leave the operating position (behind the handles). Wait until the auger/impeller comes to a complete stop before unclogging the discharge chute, making any adjustments, or inspections. 18. Never put your hand in the discharge or collector openings. Always use the clean-out tool provided to unclog the discharge opening. Do not unclog discharge chute while engine is running.Shut off engine and remain behind handles until all moving parts have stopped before unclogging. 19. Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains, cabs etc.). 20. If situations occur which are not covered in this manual, use care and good judgment. Contact your dealer or telephone 1-800-800-7310 for assistance and the name of your nearest servicing dealer. MAINTENANCE AND STORAGE 1. Never tamper with safety devices. Check their proper operation regularly. Refer to the maintenance and adjustment sections of this manual. 2. Before cleaning, repairing, or inspecting machine disengage all clutch levers and stop engine. Wait until the auger/impeller come to a complete stop. Disconnect the spark plug wire and ground against the engine to prevent unintended starting. 3. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage. 4. Do not change the engine governor setting or over-speed the engine. The governor controls the maximum safe operating speed of the engine. 5. Snow thrower shave plates and skid shoes are subject to wear and damage. For your safety protection, frequently check all components and replace with original equipment manufacturer’s (OEM) parts only. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!” 6. Check clutch controls periodically to verify they engage and disengage properly and adjust, if necessary. Refer to the adjustment section in this operator’s manual for instructions. 7. Maintain or replace safety and instruction labels, as necessary. 8. Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment. 9. Prior to storing, run machine a few minutes to clear snow from machine and prevent freeze up of auger/impeller. 10. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer etc. 11. Always refer to the operator’s manual for proper instructions on off-season storage. WARNING: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. 4 SECTION 2: CONTENTS OF HARDWARE PACK Lay out the hardware according to the illustration below for identification purposes. Part numbers are shown in parentheses. (Hardware pack may contain extra items which are not used on your unit.) A ATTACHING THE HANDLES Hex Bolts 710-3259 (2) Hex Bolts 710-1880 (2) Lock Washers 736-0119 (4) Saddle 784-5599 (2) B ATTACHING HANDLE PANEL Carriage Bolts 710-0262 (4) Hex Patch Nuts 712-3068 (4) Lock Washers 736-0119 (4) C D ATTACHING CLUTCH CABLES AND SHIFT ROD Z Fitting 746-0778 (2) Hex Nuts 712-0121 (2) E ATTACHING CHUTE ASSEMBLY Hex Bolts 710-3015 (2) Hex Lock Nuts 712-3027 (6) Chute Flange Keepers 731-0851 (3) Not Shown F ATTACHING CHUTE DIRECTIONAL CONTROL Flat Washers 736-0185 (2) Cupped Washer 736-0242 Hex Nuts 712-3010 (2) Hairpin Clip 714-0104 Eyebolt (Not Shown) 747-0697 Ferrule 711-0677 Hairpin Clips 714-0104 (2) Flat Washers 7736-0275 (2) Hex Lock Nuts 712-0429 (2) REPLACEMENT SHEAR BOLTS Hex Bolts 710-0890A (2) Hex Screws 710-3103 (2) Spacer 750-1032 (2) Hex Top L-Nut 712-0429 (2) ATTACHING THE CLUTCH GRIPS G (Z Fittings might be already attached to cables) NOTE: The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. If you hit a hard foreign object or an ice jam, the snow thrower is designed so that the bolts may shear. Two replacement shear bolts and nuts are provided for your convenience. Store in a safe place until needed 5 6 SECTION 3: ASSEMBLING YOUR SNOW THROWER NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position. The “operator’s position” is defined as standing directly behind the snow thrower, facing the handle panel. Unpacking • Remove staples or break glue on top flaps of the carton. Remove any loose parts included with uni...
Эта инструкция также подходит к моделям:Снегоочистители - 642E (6.04 mb)
Снегоочистители - 642F (6.04 mb)
Снегоочистители - 644E (6.04 mb)
Снегоочистители - 662E (6.04 mb)