Оценок - 3, средний балл: 4 ( )

Производитель: Bolens Размер: 6.04 mb Название файла: Язык инструкции:

The triangular metal tab on the auger control grip must face the center of the handle panel. See Figure 3. Figure 3 • Place the auger control on top of the left handle. The triangular metal tab must be between the handle and the bracket. See Figure 3. • Secure with hex bolt, spacer, and hex lock nut. Do not overtighten this bolt as it will prevent the control from automatically returning to their upright position. See Figure 4. Handle Panel Auger Control Traction Control Left Handle Right Handle Left Clutch Bracket Right Clutch Bracket Handle Panel Carriage Bolts Left Bracket Lock Washers Left Handle Hex Patch Nuts (Curves in) Auger Control “Z” Fitting Triangle Metal Tab Triangle Metal Tab 7 Figure 4 • Repeat process for the right side Traction Control. • Lay handle assembly behind snow thrower. See Figure 5. • Insert a hex bolt 3/4” long and lock washer through the lower hole on the bottom of the handle. • Hold the handle assembly up to the bottom of the snow thrower frame and thread the hex bolt into the lower hole in snow thrower frame. Do not tighten at this time. See Figure 5. • Repeat process on the other side. Figure 5 • Raise the handle assembly into the upright position and align the top holes in the handle with the top holes in the snow thrower frame. Attach using 2” long hex bolts, lock washers and saddles. (Curve in saddle must match the curve in the handle.) See Figure 6. • Tighten all hardware used to attach the handle assembly to the snow thrower frame. Figure 6 Attaching Shift Rod (Hardware D) • Place the shift lever in the fastest forward speed position. • Models 602, 642, and 662: Rotate the shift arm assembly counter clockwise, as far as it will go. Insert the shift rod through the shift arm assembly. When installed the shift arm assembly should point to the right. Secure with flat washer and hairpin clip. See Figure 7. • Models 602, 642, and 662: Thread the ferrule up or down the shift rod and align with the lower hole on the shift lever assembly behind the handle panel. See Figure 7. Figure 7 • Models 614, 644, 664 and 6A4: Rotate the shift arm assembly counter clockwise as far as it will go. Insert the shift rod through the shift arm assembly. When installed, the shift arm assembly should point left. Secure with flat washer and hairpin clip. See Figure 8. Auger Control Left Bracket Handle Panel Spacer Hex Lock Nut “Z” Fitting Left Handle Hex Bolt Hex Bolt & Lock Washer Handle Panel & Handles Cable Roller Guide Lock Washers 3/4” Hex Bolt 2” Hex Bolt Saddle Models 602, 642 and 662 Shift Lever Traction Drive Clutch Hairpin Clip Ferrule (Bottom Hole) Flat Washer Shift Rod Shift Arm Assembly Hairpin Clip Flat Auger Drive Clutch Washer 8 • Models 614, 644, 664, and 6A4: Thread the ferrule onto the shift rod, up or down the shift rod and align with the far hole on the narrow side of the shift lever assembly behind the handle panel. See Figure 8. Figure 8 • Secure the ferrule to the shift arm assembly with the flat washer and hairpin clip. Attaching Clutch Cables (Hardware D) Z fittings with jam nuts might be already inserted in each control lever (on the handle panel) at the factory. To attach the cables to the Z fittings, proceed as follows: NOTE: Two extra jam nuts are included in the hardware pack in the event either are lost during shipping. • If Z fittings are not already attached, thread hex nuts onto the “Z” fittings and insert “Z” fitting into hole in clutch grips. See Figure 9. • Route the left cable between engine and speed selector plate and then between handle panel and clutch lever pivot rod before threading onto the left “Z” fitting. Figure 9 • Assemble the right cable in the same manner. • Both cables should have minimal slack, but not tight. • If Z fittings are already attached, thread the jam nuts all the way up each of the Z fittings, toward the handle panel. • Make certain all cables are in the grooves of the cable roller guides in the lower rear of the unit, one on each side. Refer to Figure 6. • Thread the coupling end of the cable onto the threaded portion of the Z fitting until the rubber bumper (located on the underside of the clutch lever) only lightly contacts the upper handle. IMPORTANT: The cable should have very little slack, but should NOT be tight. An overtightened cable may prohibit the auger and drive from disengaging. WARNING: Over-tightening the cable may prohibit the auger and drive from disengaging and compromise the safety of the snow thrower. Do NOT overtighten the cable. • Once properly adjusted, tighten the jam nut against the coupling end of the cable to lock it in position. NOTE: Refer to Auger Control Test in the Operation Section prior to operating your snow thrower. Read and follow all instructions carefully and perform all adjustments to verify your snow thrower is operating safely and properly. Attaching the Chute Assembly (Hardware F) • Place chute assembly over chute opening, with the opening in the chute assembly facing the front of the unit....

Скачать инструкцию

Чтобы скачать, введите 2 цифры: