Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
• To turn the tool ON, rotate the knob clockwise. The further the knob is rotated, the higher the air speed. • To turn tool OFF, rotate the knob counterclockwise to the off position (0). MODEL LH4500 Your blower vac is fitted with a two speed switch located on the top of the power head below the handle. • To use in low speed, rotate the knob clockwise to Position I. To use in high speed, rotate the knob clockwise to Position II. • To turn tool OFF, rotate the knob counterclockwise to the off position (0). 9 8 7 10 5 MODEL BL1500 Your blower is fitted with a single speed switch located on the top of the power head below the handle. • To turn the tool ON, rotate the knob clockwise to Position I. • To turn tool OFF, rotate the knob counterclockwise to the off position (0). CORD RETAINER (FIGURE 11) • A cord retainer is incorporated into the rear of the power head. It can be used in two different ways: • To use the cord retainer as shown in figure 11A, hook the extension cord under the retainer. Then plug the cord from the power head into the extension cord. • To use the cord retainer as shown in figure 11B, loop the extension cord over the power head cord and plug the two ends into each other. Then hook the extension cord under the retainer. BLOW MODE (FIGURE 12) WARNING: Ensure product is switched off and disconnected from the power supply. • Fit grill cover as shown in figure 1. • Attach the blow tube assembly to the power head as shown in figure 2. • Connect the cord on the power head to the power supply (figure 11). • Hold the blow tube approximately 7 inches (180mm) above the ground, turn the blower/vac on and using a sweeping motion from side to side, advance slowly keeping the accumulated debris/leaves in front of you. • Once you have blown the debris/leaves into a pile, you can convert to vacuum mode to collect the debris. • Using the air concentrator will help remove matted debris and leaves. • Using the leaf blaster attachment will help move air back and forth to remove stubborn debris from grassy areas. VACUUM MODE (FIGURE 13) MODELS (LH4500, LH5000 ONLY) USE AS A VACUUM: WARNING: Ensure product is switched off and disconnected from the power supply. To fit the shoulder collection bag to product: • Remove blow tube. • Attach the shoulder collection bag to the power head as shown in figure 5. • Remove the fan cover from the bottom of the power head by pressing the spring loaded release button (located on the back of the power head) and pulling the cover off (figure 7). • Attach the vacuum tube assembly to the power head (figure 8) by locating the assembly as indicated by arrow, then pivot about this point until the locking/release catch is fully engaged. • Connect the cord on the power head to the power supply (figure 11). • Position the tube slightly above the debris/leaves. Turn the blower/vac on, then using a sweeping motion the debris/leaves will be sucked up the tube, mulched and deposited into the collection bag (figure 13) . 11 12 13 11A 11B 6 As the bag fills the power of the suction will decrease, turn the blower/vac off and unplug from power supply. FOR LH5000 BAG: • Empty the shoulder collection bag by sliding the retaining bar off the bottom of the bag as shown in figure 14. CAUTION: NEVER REMOVE THE COLLECTION BAG WITHOUT FIRST TURNING OFF AND UNPLUGGING THE VACUUM. NOTE: If the suction decreases and the bag is not full, the vacuum tube is probably clogged with debris. Turn off and unplug the blower/vac and clear the tube before continuing. • To reattach the retaining bar, close the bottom of the shoulder bag by folding the bi-folds flat as shown in figure 15. Slide the retaining bar over the closed bag. FOR LH4500 BAG: As the bag fills the power of the suction will decrease, switch off your product and unplug from power supply. Unzip the bag to empty before continuing to operate. MAINTENANCE • CLEANING AND STORAGE TURN OFF AND UNPLUG TOOL! (Unplug extension cord at power source.) Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Clean out any clippings which may have accumulated in the Blower/Vac. When used properly with dry leaves the fan chamber of your Blower/Vac should remain clean. If damp earth and debris are ingested some of the particles may build up on the inside of the fan chamber. If this happens the performance of the unit will decrease. This area can be cleaned out using a wooden stick as shown in figure 16 after disconnecting from the power source. Your Blower/Vac should be stored in a dry place. WARNING: SHOCK HAZARD. DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN. Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts. 141516 7 Important To assure product SAFETY and RELIABILITY; repairs, maintenance and adjustments (other than those listed in this manual) should be performed by authorized serv...
Эта инструкция также подходит к моделям:Системы вентиляции - BL1500 (3.8 mb)
Системы вентиляции - LH5000 (3.8 mb)