The P.C. Board causes the motor to run in a forward direction when the "ON” Switch is actuated and turn off when the "OFF/REVERSE" is momentarily depressed. When the "OFF/REVERSE" Switch is held down PCB1 reverses direction of the motor. If the motor stops due to a jam, PCB1 will reverse the direction of the motor then shut off after the jam has been ejected. When the "ON" button is depressed, contacts A and B of SI close momentarily completing a circuit between PCB1-1 and PCB1-3. At this time

For a safe operation of the trimmers it is important, that the knife guard is not taken off. The knife carrier (#3) is fitted with a friction device. If adjusted correctly, this friction device insures, that the knife carrier (#3) with the knife cannot move down on its own from any position. If the blade and blade carrier fall by themselves the friction device must be adjusted as follows: For the model 1038 loosen the set screw (I). Tighten the lock nut (II) and retighten the set screw (I). F

abcoffice. com (800) 658-8788 Models 112, 115, 118, 124 6 2 Thank you for selecting Dahle to be your Paper Cutter company. We trust you will be thoroughly satisfied with your purchase. Dahle cutters are highly regarded world-wide for their precision, reliability, and durability. In addition, all Dahle cutters are individually tested and must meet the most stringent performance standards. During use, please observe the following suggestions for care, maintenance and proper operations: • Y

In addition, the cutting board is printed with V2“ grid lines (#2), which acts as an excellent visual aid in achieving a straight T-square cut. • Insert the material to be cut under the clamp/safety guard (#3). • Align material at desired position on inch/cm scale (#1). Material should be flush with paperstop (#4), and parallel to the printed grid lines (#2). • Depress the material to be cut with the clamp. The clamp will secure the material in position, preventing slippage. While clamping th

If it moves too easily, it can be adjusted with the bolt assembly located at the fulcrum (#9). In order to do so, remove the screw (#5) first and take off the lid (#6). Then tighten the hex nut (#7) and the screw (#8) in a counter-action, thus adjusting the pressure of the upper blade against the lower one. At last put the lid back on and secure with the screw. Cutting Board Surface - The cutting board should be cleaned periodically, or as often as required, in order to retain it’s original lus

7. Operation Read operating instructions before operating the shredder. Insert plug in power outlet. To avoid motor overload, the paper shredders may cut out automatically after approx. 20 minutes of continuous operation. Switching equipment ON 1 – Press rocker switch to pos. (1) • Controller switch locks in "on" position. • Equipment is ready for operation (standby). – Feed paper • The shredding process is started by automatic start stop control in the paper feed opening. Insert paper and shred

We have made many improvements in our commercial shredder since its introduction in 1982. We are confident that it offers you the greatest value for your money in its product category today. We hope it meets – or even exceeds – your expectations. To ensure years of safe, efficient use, please read these few pages about your new shredder. If this manual doesn’t answer all your questions or if you wish to comment on this product, we welcome your call or letter. Sincerely, James Fellowes Chairman &

. . . . . . . . . . . . . . . . . . . Warranty . . . . . . . . . . . . . . . . . . . . . . Product Profile This product is built to shred paper, staples, small paper clips and credit cards. It is not built to shred adhesive labels, transparencies, newspaper, cardboard, large paper clips, or plastic (other than credit cards). Attempting to shred items not intended for this shredder may cause damage. Strip- cut Confetti- cut (120-2/C-120) (120C-2/C-120C) Paper Sheet capacity* 18-20 sheets 12-14 sh

CAUTION: The shredder may be damaged if you alternate too rapidly between forward and reverse. • Unplug shredder and remove wastebasket drawer (A). – Carefully clear any paper shreds that have collected on under side of paper entry (C). CAUTION: Model 120C-2 (confetti cut model) has exposed blades.Use care when removing paper shreds on underside of paper entry. To clear a paper jam If paper jam light (J) is on, follow these steps until light turns off. • Check the waste basket and empty if full.

CAUTION: The shredder may be damaged if you alternate too rapidly between forward and reverse. • Unplug shredder and remove wastebasket drawer (A). – Carefully clear any paper shreds that have collected on under side of paper entry (C). CAUTION: Models 120C-2/C-120C (confetti cut model) has exposed blades.Use care when removing paper shreds on underside of paper entry. To clear a paper jam If paper jam light (J) is on, follow these steps until light turns off. • Check the waste basket and empty