Оценок - 1, средний балл: 4 ( )

Производитель: Black & Decker Размер: 3.06 mb Название файла: Язык инструкции:

Engage the clamp washer threads on the tool spindle and thread assembly clockwise, completely down on the spindle. Hold the spindle from rotating by engaging the spindle lock button. To remove the abrasive disc, use a cloth or glove to protect your hand. Turn the disc assembly counterclockwise (Figure 8). Hold the spindle from rotating by engaging the spindle lock button. Figure 6 BACKING*PAD CLAMP WASHER SPINDLE LOCK BUTTON Figure 8 BUTTON Sanding (6138 only) (See Figure 9) When using an abrasive disc, hold the tool so that an angle of 10° to 15° exists between the disc and the work. If only the outer edge of the sanding disc is used, a rough cut will result. If the sanding disc is pressed flat against the work, the sanding action will be irregular and bumpy, and the tool will be difficult to control. Figure 9 MAINTENANCE Cleaning Blowing dust, polishing bonnet lint, and grit out of the motor housing using compressed air is a necessary regular maintenance procedure. Dust and grit containing metal particles often accumulate on interior surfaces and could create an electrical shock hazard if not frequently cleaned out. CAUTION: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. Use clean, dry rag only. Lubrication B&D tools are properly lubricated at the factory and are ready for use. Tools should be relubricated regularly every sixty days to six months, depending on usage. (Tools used constantly on production or heavy-duty jobs and tools exposed to heat may require more frequent lubrication.) This lubrication should only be attempted by trained power tool repairpersons such as those at B&D service centers or other authorized service locations. Motor Brushes Be sure tool is unplugged before inspecting brushes. Carbon brushes should be regularly inspected for wear. To inspect brushes, unscrew the plastic brush inspection caps (located in the sides of the motor housing) and the spring and brush assemblies may be withdrawn from the tool. Keep brushes clean and sliding freely in their guides. Carbon brushes have varying symbols stamped into them, and if the brush is worn down to the line closest to the spring, they must be replaced. New brush assemblies are available at service centers; see Tool, Electric in the yellow pages. Your tool is equipped with the B&D brush CHECKPOINT™ system. When the brushes become worn out, the tool will automatically stop and prevent damage to the motor. ACCESSORIES Recommended accessories for use with your tool are available at extra cost from your distributor or your local service center. A complete listing of service centers is included with your tool. Use only accessories having a maximum operating speed at least as high as the highest “NO LOAD RPM” marked on the tool’s nameplate. This precaution applies to any accessory on any tool. CAUTION: The use of any non-recommended accessory may be hazardous. If you need any assistance in locating any accessory, call 1-800-9-BD TOOL (1-800-923-8665) or contact Black & Decker, Consumer Services Department, P.O. Box 618,626 Hanover Pike, Hampstead, MD 21074. Rubber Backing Pads: C51824 7" Quick Change Super Flexible Rubber Backing Pad (includes #50933 Clamp Washer) Polishing Bonnets and Pads: B&D has an array of polishing bonnets and pads for 7" and 9" polishers. See your local B&D service center. Important! To assure product safety and reliability, repairs, maintenance, and adjustments should be performed by B&D service centers or other qualified service organizations, always using B&D replacement parts. 8 Every B&Q tool 1$ of the highest quality. If you wish to contact us regarding this product, please mil toll tfBft B61W68I) o.Uuam 3M 8«w^uti 11 $ sgvbb diijfs 8 W60&# 1-800-9-BD TOOL One Year Free Maintenance All B&D tools for Industry and Construction are covered under a service/safety check program where B&D will inspect your tool for safety and provide necessary maintenance or repairs, including normal wear and tear parts, for one year, FREE OF CHARGE. Full Warranty All B&D tools for Industry and Construction are warranted to be free of any defects in materials or workmanship. Upon thorough examination of tool, B&D will repair or replace, at our option, any product that is determined to be defective. Conditions The service/safety check and the warranty do not apply to: repairs made or attempted by anyone other than an authorized B&D service location; misuse, abuse, neglect, improper application of the tool; missing parts; or normal wear and tear (after first year of ownership). Please return the complete unit, transportation prepaid, to any B&D factory owned or B&D authorized service center location (list provided with tool or see yellow pages under “Tools Electric”). These symbols on the nameplate mean the product is listed by Underwriters Laboratories, Inc. and certified by the Canadian Standards Association. BlackS Decker (U.S.) Inc. • 701 East Joppa Ro...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: