Оценок - 4, средний балл: 3.8 ( )

Производитель: American Standard Размер: 701.84 kb Название файла: Язык инструкции:

Fig. A. DRAIN BODY 4 2 DRAIN OUTLET 1 3 4 REAR OF SINK M965016 REV.1.7 8 CHECK OPERATION OF POP-UP 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. Fig. A. 7 ATTACH CABLE CONNECTOR 2 1 Fig. B. 1-1/4” O.D. 3 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 1 APPROX. 20" 2 HOT COLD 3/8" COMPRESSION RED BAND BLUE BAND Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left SUPPLY (1) to Hot (Marked with a Red Band) and right supply to COLD (2) wall supply. Faucet supplies are 20" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately. Important: If SUPPLY HOSES (1, 2) are to long, loop as illustrated to avoid kinking. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 2 1 M965016 REV.1.7 12 11 4 2 8 2.5mm HEX KEY 5 6 3 4 7 REMOVE INSTALL SERVICE To remove or replace cartidge: Fig. A. Turn valve to OFF position. Remove HANDLE SCREW (2). Pull off HANDLE (3) and CAP (4). Unthread CARTRIDGE NUT (5) and remove. Pull out CARTEIDGE (6). Inspect CARTRIDGE (6) and O-RING (7) for debris and clean if necessary. Clean MANIFOLD (8) and rinse clean. Reinstall CARTRIDGE (6) and O-RING (7) onto MANIFLOD (8). Reinstall CARTRIDGE NUT (5), CAP (4) and HANDLE ASSEMBLY (3). If spout drips, operate handle several times from OFF to ON and HOT to COLD position. Do not force - handles turn only 90°. Turn off hot and cold water CAUTION supplies before beginning. 2 TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). 5 4 2 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions. Release POP-UP KNOB (4) down and check all drain connections and "P" trap for leaks. Tighten if necessary. 10 “P” TRAP WASTE OUTLET 3 1 OFF ON COLD HOT To change from swivel to fixed spout, proceed as follows: Remove SET SCREW (1) using Hex Wrench supplied. VIEW “A” Install FIXING SET SCREW (2) using Hex Wrench supplied. Align SPOUT (3) and tighten SET SCREW (2) to secure SPOUT (3). CONVERT TO A FIXED SPOUT IF DESIRED. Fig. B. 7420.101 ONLY. SPOUT CAN BE FIXED OR SWIVEL. 1 3 2 VIEW "A" DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, PO...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: