Careful use and timely service saves extensive repairs and costly downtime losses. Please read this manual thoroughly. Understand what each control is for and how to use it. Rhino typically offers three types of shielding to protect the operator, passerby, livestock, and property from thrown objects... deflectors, single chain guards, and double chainguards. Shielding should be selected based on the intended use of the mower. Double chainguards or deflectors should be used for highway, right-of-

• Ensure the driveline integral shield is in good condition and rotates freely. • Ensure the driveline slip clutch (if equipped) is properly adjusted. OPS-R-0039 OPERATION © 2011 Alamo Group Inc. OPERATION TW120 01/11 Operation Section 4-23 • Inspect the gearbox oil level. A low oil level is a warning sign that the gearbox may be cracked or its seal is damaged and needs replacement. • Ensure the gearbox vent is in place and free from clogs. OPS-R-0040_C • Inspect blades and blade bolts for loose

When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! ! © Copyright 2012 Printed 20583 313-306M PSN2096 Primary Seeder Operator’s Manual 5/15/12 Table of Contents Important Safety Information . . . . . . . . . . . . . 1 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . .1 Look For The Safety Alert Symbol . . . . . . . . . . . . .1 Safety Labels . . . . . . . . . . . . . . . . .

(Normal gap is 3".) 54 B. Single Tine Replacement 3. Raise the hood flap at the back of the tiller and tie it up with string. r A WARNING The tines or tine hood edges may be sharp. Wear thick gloves to protect your hands from cuts or scrapes. 1. Move the Wheels/Tines/PTO Drive Lever to NEUTRAL, the Wheel Speed Lever to either FAST or SLOW position, and the Tines/ PTO Clutch Lever to ENGAGE. 2. Gently tilt the tiller forward until the engine rests on the ground. C. Removing and Replacing

Failure to tighten or replace fasteners can cause poor performance, equipment damage or oil leakage. See your Parts Catalog for complete fastener descriptions. Most hardware on your tiller is visible. Pay particular attention to hardware shown in Photos 5-1,5-2, 5-3, and Figure 5-3A. 1. Check the transmission pulley mounting bolt (Photo 5-1). If the washer behind the bolt head is loose, the bolt needs tightening. To do this, first insert a punch or thick screwdriver into the hole next to the

Thereafter, check them every 30 hours. 3. Check Drive Belt Tension. Due to belt seating, a tension adjustment may be needed after the first 2-to-3 hours of new operation. Thereafter, check belt tension every 10 operating hours. 4. Check Hardware. After 2 hours of new operation, check for loose bolts and nuts. Thereafter, do this every 10 operating hours. Preparation Before Starting Make the following checks and perform the following services before starting the engine. 1. Check Engine Oil

The only tool you will need is a 3/4" wrench (minimum 12" long for good leverage). There are two optional accessories that make the following steps easier. The Kickstand accessory prevents the PTO Power Unit (engine end) from falling forward CAUTION TO AVOID PERSONAL INJURY OR DAMAGE TO EQUIPMENT: • Stop the engine, remove the electric start key, disconnect the spark plug wire and let the engine and muffler cool before removing or installing any attachment. • Do not place hands, tools, or a

5-8). Don’t force or try to thread it back in...an incorrect reading will result. 7. Remove dipstick and check oil level. It should be anywhere within the cross-hatched area or even slightly above the “Max” marking. If correct, replace dipstick and remove the boards used as props. 8. If oil level was low, gear oil must be added before using the tiller. See “C. Adding or Changing Gear Oil” next. For Dipsticks With Hot/Cold Markings: 1. Follow Steps 1 and 2 given for the other type of dipstick

Avoid spills or contact with skin, eyes, clothing. • To prevent accidents, wear protective clothes, rubber gloves and shield eyes with safety goggles when working on or near the battery. • Neutralize acid spills with a baking soda and water solution. Neutralize electrolyte container with same solution. Then rinse with clear water. Antidote: External- Flush with water; Eyes- Flush with water for 15 minutes and get immediate medical attention. Antidote: Internal- Drink large quantity of water o

The safety decal locations are shown (at a reduced size) below. There are other decals located on your equipment for operation and controls identification. They are also shown below and in your Parts Catalog. If you need a replacement decal, please refer to the Parts Catalog that accompanied this Manual. Decal Locations A) WARNING: Hot Surfaces decal. On 8HP Kohler engines (shown), located on top of the engine. On Briggs & Stratton engines (not shown), located on top of the muffler guard. F)