A blade with worn teeth besides providing poor performance might also generate a sudden thrust. This can result in a violent sideways kick caused when the blade touches against wood or solid bodies, such thrust might then cause the operator to loose control of the machine itself. Never attempt to work with a damaged blade but replace it with a new one. THRUST: can occur when using any type of circular blade within the risk area: therefore it is advisable to cut using the remaining area of the bl

A no. 3). In fact, the trigger (fig. A no. 3), can only be pressed if the safety lever is pressed at the same time (fig. A no. 19). By means of 2 separate springs, upon eleasing the grip, the throttle trigger (fig. A no. 3) and safety lever (fig. A no. 19) return automatically to their original positions. Engine stop device the stop button Stop (fig. A no. 7) to O / STOP to stop the engine. To make sure this button works properly, start the engine and check that it stops when the Stop button is

7 VIBRATIONS LEVEL BLADE (ISO 7916) (m/s2) MAX-MIN 9,05-1,8 9,05-1,7 i DATI TECNICI CILINDRATA (cm3) 34 38 ALESAGGIO x CORSA (mm) 38x30 40x30 POTENZA (Kw) 1,2 1,3 REGIME DI MASSIMA POTENZA (min-1) VELOCITA MAX A VUOTO (min-1) VELOCITA DI MINIMO (min-1) VELOCITA ALBERO PORTALAMA (min-1) 8.000 10.000 2.800 7.700 8.000 10.000 2.800 7.700 COPPIA SERRAGGIO DADO BLOCCALAMA (Nm) 17 17 PESO A SECCO (Kg) CAPACITA SERBATOIO MISCELA (cm3) 7,1 900 7,3 900 PRESSIONE SONORA (ALL’ORECCHIO DELL’OPERATORE) LpAav

NOTE: For proper operation, always refer to the instructions accompanying the trimmer head being used. Trimmer head styles: Semi-automatic. Trimmer line is indexed when the operator taps the trimmer head on the ground during operation. Manual. The operator indexes line manually with the grass trimmer stopped. Fixed. The operator must stop the unit and add new lengths of trimmer line manually. Flail. This device, designed for clearing weeds and light brush, features three nylon blades attached to

As the engine owner, you should however be aware that Shindaiwa Corporation may deny your warranty coverage if your engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. You are responsible for presenting your engine to the nearest dealer authorized by Shindaiwa Corporation when a problem exists. If your Shindaiwa Dealer is unable to answer questions regarding your warranty rights and responsibilities, you should then contact your Shindaiwa Distribu

NOTE: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized Shindaiwa dealer. Adjusting Engine Idle The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment. WARNING! The cutting attachment must NEVER rotate at engine idle! If the idl

des Schlagblattes achtgeben Auf hochgeschleuderte Gegenstande achtgeben Sicherheitsabstand Luftklappe offen (Starten bei warmem Motor) Luftklappe geschlossen (Starten bei kaltem Motor) e No utilice cuchillas metalicas Velocidad maxima de la cuchilla Advertencia Precaucion Cuidado con la reaccion de la cuchilla Tenga cuidado con los objetos proyectados Distancia minima de seguridad Estrangulador totalmente abierto (Arranque en caliente) Estrangulador cerrado (Arranque en frio) hGebruik geen metal

Always wear eye and hearing protection when operating this unit. Part Number 81359 Rev 8/06 Attention Statements Introduction Safety Instructions Throughout this manual are special “attention statements”. The Shindaiwa 242 Series hand held power equipment has been designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Shindaiwa engines represent the leading edge of high-performance engine technology, delivering exceptional

..D.D.D... ... ....... ....D....... .D. ...R..D.... ..D ........D ...M .... ..D..D..... ...D.D..... i A gyarto ceg fenntartja a jogot arra, hogy a hasznalati utasitasban megadott adatokon es technikai tulajdonsagokon barmikor es elozetes bejelentes nelkul valtoztasson. A A A. GENERAL DESCRIPTION 1) ENGINE 2) SHAFT 3) THROTTLE TRIGGER 4) THROTTLE ADVANCE 7) NYLON STRING HEAD 8) STOP SWITCH 9) CHOKE LEVER 10) STARTER HANDLE 11) HARNESS RING B. SAFETY RULES 1) Make sure all operators study this man

A guard or other part that is damaged should be properly repaired or replaced by an authorized service center, unless otherwise indicated in this instruction manual. 13. RESTER VIGILANT: Attention a ce que vous faites. Utiliser votre sens commun. Ne pas manier la tronconneuse par moments de fatigue. Rester a l’ecart de la chaine quand le moteur est en marche. Avant de mettre le moteur en marche, s’assurer que la chaine ne touche rien. 14. ENTRETENIR LA TRONCONNEUSE AVEC SOIN: Verifier les cordon