Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
2. Loosen fuel cap slowly to release pressure and to keep fuel from escaping around the cap. 3. Carefully pour fuel mixture into the tank. Avoid spillage. 4. Prior to replacing the fuel cap, clean and inspect the gasket. 5. Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage. Move 9 m (30 ft) away from refuelling site before starting engine. NOTE: It is normal for smoke to be emitted from a new engine during and after first use. WARNING: Always shut off engine before refuelling. Never add fuel to a machine with a running or hot engine. Move at least 9 m (30 ft) from refuelling site before starting engine. Do not smoke! 1 Litre + 20 ml = 2 Litres + 40 ml = 3 Litres + 60 ml = 50:1 4 Litres + 80 ml = } 5 Litres + 100 ml = OPERATING THE TRIMMER Hold the trimmer/brushcutter with the right hand on the trigger handle and the left hand on the left handle.Keep a firm grip with both hands while in operation.Trimmer should be held at a comfortable position with the trigger handle about hip height. See Figure 9. Always operate trimmer at full throttle. Cut tall grass from the top down.This will prevent grass from wrapping round the shaft housing and string head which may cause damage from overheating. If grass becomes wrapped round the string head, stop the engine, disconnect the sparking plug wire, and remove the grass. Prolonged cutting at partial throttle will result in oil dripping from the silencer. 11 12 ADVANCING THE STRING ADVANCING STRING USING THE EZ LINE™ TAP ADVANCE SYSTEM String advance is controlled by tapping string head on grass while running engine at full throttle. 1. Run engine at full throttle. 2. Tap string head on ground to advance string. String advances each time the head is tapped. 3. Several taps may be required until string strikes the cut off blade. 4. Resume trimming. NOTE: If the string is worn too short you may not be able to advance the string by tapping it on the ground. If so, STOP THE ENGINE, and manually advance the string. ADVANCING THE STRING MANUALLY Push the spool retainer down while pulling on string(s) to manually advance the string. GRASS DEFLECTOR LINE TRIMMING CUTOFF BLADE See Figure 11. This trimmer is equipped with a line trimming cut-off blade on the grass deflector. For best cutting, advance string until it is trimmed to length by the cut-off blade. Advance string whenever you hear the engine running faster than normal. This will maintain best performance and keep string long enough to advance properly. CUTTING TIPS See Figure 10. ¦ Keep the trimmer tilted toward the area being cut; this is the best cutting area. ¦ Do not cut in dangerous cutting area. ¦ Use the tip of string to do the cutting; do not force string head into uncut grass. ¦ Wire and picket fences cause extra string wear, even breakage. Stone and brick walls, kerbs and wood may wear string rapidly. ¦ Avoid trees and shrubs. Tree bark, wood mouldings, cladding and fence posts can easily be damaged by the string. Fig. 9 OPERATION Fig. 11 DANGEROUS CUTTING AREA Fig. 10 BEST CUTTING AREA DIRECTION OF ROTATION 13 WARNING: Extreme care must be taken when using blades to insure safe operation. Read the safety information for safe operation using the blade, refer to “Specific Safety Rules for Brushcutter and Blade Use” earlier in this manual. ¦ Always hold brushcutter with both hands when operating. Use a firm grip on both handles. ¦ Maintain your grip and balance on both feet. Position yourself so that you will not be drawn off balance by the kick-back reaction of the cutting blade. ¦ Inspect and clear the area of any hidden objects such as glass, stones, concrete, fencing, wire, wood, metal etc. ¦ Never use blades near footpaths, fencing, posts, buildings or other immovable objects. ¦ Never use a blade after hitting a hard object without first inspecting it for damage. Do not use if any damage is detected. ¦ Scythe, the broad sweeping of the unit back and forth from side to side, with TRI-ARC blade only. Exercise extreme caution when using the blade with this unit. Blade thrust is the reaction which may occur when the spinning blade contacts anything it cannot cut. This contact may cause the blade to stop for an instant, and suddenly “thrust” the unit away from the object that was hit. This reaction can be violent enough to cause the operator to lose control of the unit. Blade thrust may occur without warning if the blade snags, stalls or binds. This is more likely to occur in areas where it is difficult to see the material being cut. For cutting ease and safety, approach the weeds being cut from the right to the left. In the event an unexpected object or woody stock is encountered, this could minimise the blade thrust reaction. See Figure 13. OPERATING THE BRUSHCUTTER Hold the brushcutter with the right hand on the trigger handle and the left hand on the left handle. Keep a firm grip with both hands while in operation. Brushcutter should be held at a comfortable position with the trigger han...
Эта инструкция также подходит к моделям:Садовые инструменты - UT70129 (522.38 kb)