Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
457 mm Engine displacement ................................................................................................................................................ 30 cm3 Maximum engine performance (in accordance with ISO 8893) ............................................................................... 0.78 kW Maximum rotational frequency of the spindle ...................................................................................................10,000/min-1 Engine Speed (rotational frequency) at recommended max. spindle rotational frequency .................................12,500/min-1 Engine speed (rotational frequency) at idle .............................................................................................2,000 - 2,500/min-1 Fuel consumption (in accordance with ISO 8893) at max. engine performance ................................................... 0.52 kg/h Specific fuel consumption (in accordance with ISO 8893) at max. engine performance ...................................... 0.47 kg/h Vibration level idling Left Handle ........................................................................................................................... 9.3 Right Handle ....................................................................................................................... 12.4 Vibration level racing Left Handle ........................................................................................................................... 7.5 Right Handle ....................................................................................................................... 12.5 Sound pressure level (in accordance with EN ISO 11806:1997, ISO 7917:1987) ............................................................ 99 Sound power level (in accordance with ISO 10884) ....................................................................................................... 110 5 6 Fig. 1 THROTTLE TRIGGER STARTER GRIP ENGINE HOUSING THROTTLE INTERLOCK IGNITION SWITCH TRI-ARC BLADE BLADE GUARD SHAFT HOUSING STRAP HANGER SHOULDER STRAP LEFT HANDLE GEAR HEAD TRIGGER HANDLE UNPACKING INSTRUCTIONS ¦ Carefully remove the product from the carton. ¦ Inspect the product to make sure no breakage or damage occurred during carriage. ¦ Do not discard the packing material until you have inspected and operated the product. PACKING LIST FOR OWNER’S KIT ¦ Grass deflector ¦ Blade guard ¦ Tri-Arc blade ¦ Shoulder strap ¦ Silencer guard, torque wrench and screws ¦ Holding pin ¦ Spanners - 13 mm (1/2 in) and 16 mm (5/8 in) ¦ Fixings ¦ Operator’s manual FEATURES GRASS DEFLECTOR CUTTING LINE LINE CUT-OFF BLADE ASSEMBLY HANDLE See Figure 2. 1. Place the handlebar in the bottom clamp located on the shaft housing. NOTE: The throttle trigger must be mounted to the operator’s right side. 2. Insert the square tab of top clamp into the mounting hole of the bottom clamp. 3. Adjust the handlebar for best operator control in a comfortable upright position. 4. Install the knob and tighten securely. BOTTOM CLAMP TOP CLAMP THROTTLE TRIGGER Fig. 2 KNOB BOTTOM CLAMP TOP CLAMP THROTTLE TRIGGER BOTTOM CLAMP TOP CLAMP THROTTLE TRIGGER HANDLEBAR 7 8 ASSEMBLY SILENCER GUARD ASSEMBLY See Figure 4. 1. Remove silencer guard and two screws from the owner’s kit. 2. Attach the silencer guard to the rear housing. NOTE: Make sure the bent end of the silencer guard fits securely into the opening of the rear housing. 3. Install two screws. 4. Tighten screws securely. Fig. 4 BENT END OF SILENCER GUARD OPENING IN REAR HOUSING SCREWS SILENCER GUARD REAR HOUSING TORQUE WRENCH GRASS DEFLECTOR AND BLADE GUARD USE NOTE: When converting from brushcutter to trimmer, or trimmer to brushcutter, make sure the correct guard/ deflector is being used. See Figure 5. ATTACHING THE SHOULDER STRAP See Figure 3. 1. Connect the latch on the shoulder strap to the strap hanger. 2. Adjust the strap to a comfortable position. NOTE: To quickly release the product from the shoulder strap, sharply pull the quick release tab. SHOULDER STRAP LATCH STRAP HANGER QUICK RELEASE TAB Fig. 3 GRASS DEFLECTOR FOR TRIMMER USE BLADE GUARD FOR BRUSHCUTTER USE Fig. 5 ASSEMBLY BLADE GUARD See Figure 6. 1. Attach the blade guard to the mounting bracket; install the four screws (10-24 x 3/4 in) from the top of the mounting bracket through the blade guard and into the threaded mounting plates. 2. Using the torque wrench supplied, tighten all four screws securely. NOTE: When using the string head, the string shield must be attached to blade guard. GRASS DEFLECTOR See Figure 6. 1. Attach the grass deflector to the blade guard by placing the three locking tabs into the three notches. 2. Snap the blade guard and grass deflector together to lock into place. WARNING: Always stop the engine and remove the sparking plug wire before making any adjustments such as changing cutting heads; this is to reduce the risk of serious personal injury. CONVERTING FROM TRIMMER TO BRUSHCUTTER REMOVING THE...
Эта инструкция также подходит к моделям:Садовые инструменты - F3055 (522.38 kb)