Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer. Figure 3 Product Description C242 BRUSHCUTTER Throttle Interlock Spark Plug Ignition Switch Muffler Strap Throttle Trigger Hanger Fuel Tank Outer Tube Using the accompanying illustrations as a guide, familiarize yourself with this unit and its various components. Understanding your unit helps ensure top performance, long service life, and safer operation. Handle Bar Gear Case Cutting Attachment Shield WARNING! Do not make unauthorized modifications or alterations to any of these units or their components. Brushcutter Blade Figure 4 Specifications C242 C242 dry weight (less attachments)....................................................12.4 lb./5.6 kg Engine model.........................................................................S242E Engine type.............................................................2 cycle catalyst Bore x stroke...................................1.3 x 1.1 in./33 mm x 28 mm Displacement......................................................1.5 cu. in./23.9 cc Maximum power.....................................................1.0 HP/0.8 kW @ 8,000 RPM (min-1) Fuel/oil ratio............................50:1 with ISO-L-EGD or JASO FC class 2-cycle mixing oil* Carburetor type.............................Walbro WYK, diaphragm-type Fuel tank capacity..................................................22.3 oz./670 ml Ignition..........................................................One-piece electronic, transistor-controlled Spark plug...............................................................NGK BPMR6A Air cleaner type.........................Non-reversible foam filter element Starting method........................................................................Recoil Stopping method ............................................................Slide switch Transmission type..............................Automatic, centrifugal clutch w/bevel gear EPA Emission Compliance Period**.......................................................Category A ** The EPA emission compliance referred to on the emission compliance label located on the engine, indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. Category C = 50 hours (Moderate), B = 125 hours (Intermediate) and A = 300 hours (Extended). * meets or exceeds these specifications and is recommended for all Shindaiwa products. Specifications are subject to change without notice. This unit comes fully assembled with the exception of the handlebar, cutting attachment shield and cutting attachment. IMPORTANT! The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation. Prior to Assembly Before assembling, make sure you have all the components required for a complete unit and inspect unit and components for any damage. n Engine/Outer tube assembly n Handlebar and Throttle assembly n Cutting attachment shield n Cutting attachment n Kit containing cutting attachment shield mounting bracket and hardware, this owner’s/operator’s manual and tool kit for routine maintenance. Tool kits vary by model and may include a hex wrench, and a spark plug/screwdriver combination wrench. Assembly Cutting Attachment Shield Cutting Attachment Shield Bracket Socket- Head Cap Screw Outer Tube Shim Clamp Screw Shim Line Cutter Cutting Attachment Mounting Plate Retaining Nut Cutting Attachment Shield Sub-shield with Line Cutter Figure 5A Figure 5 Install the Cutting Attachment Shield C242 Cutting Attachment Shield 1. Insert the cutting attachment shield between the outer tube and the cutting attachment mounting plate. See Figure 5. 2. Fit the two shims and the bracket over the outer tube and loosely install the four socket-head screws. See Figure 5. 3. Tighten the four socket-head cap screws to secure the cutting attachment shield. 4. Re-tighten clamp screw and retaining nut. WARNING! NEVER operate the unit without the cutting attachment shield installed and tightly secured! NOTE: It may be necessary to loosen the retaining nut and clamp screw to adjust cutting attachment shield mounting plate. Hook Receiver Sub-Shield C242 (when trimmer head is in use) 1. Attach the shield extension to the cutting attachment shield. See figure 6. Hook Sub-shield Figure 6 WARNING! NEVER use this machine without sub-shield when using a trimmer head. CAUTION! Make sure the sub-shield is completely hooked at the hook receiver. CAUTION! Make sure the clamp screw and retaining nut are securely tightened before tightening the four socket-head cap screws. Assembly (Continued) Handle Bar C242 Install the handlebar: 1. Use the 4 mm hex wrench to remove the lower cap retaining screws from the handlebar bracket. Remove the cap from the bracket. See Figure 7. 2. Position the handle on the outer tube forward of Han...
Эта инструкция также подходит к моделям:Садовые инструменты - 81644 (3.73 mb)
Садовые инструменты - 81644 (3.73 mb)
Садовые инструменты - 81644 (3.73 mb)
Садовые инструменты - 81644 (3.73 mb)