Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
The flow of air around the dryer is essential to allow water to condense during drying; the dryer will not function properly if it is placed in an enclosed space or inside a cabinet. ! Some condensation may form if the dryer is used in a small or cold room. ! We do not recommend installing the dryer in a cupboard; moreover, never install the machine behind a lockable, sliding or hinged door located on the opposite side of the dryer door. Water drain If your dryer is installed next to a drain the water can be plumbed into this drain. This does away with the need to empty the water container. If the dryer is stacked onto or installed next to a washing machine it can share the same drain. The height of the drain must be less than 3' (1 m) from the bottom of the dryer. Remove existing hose from position shown in picture A and fit a suitable length of hose and connect as shown in picture B. ! Make sure that the hose is not squashed or kinked when the dryer is in its final location. Electrical connections Before plugging the appliance into the socket, check the following: • Make sure your hands are dry. • The socket must have an earth connection. • The socket must be able to withstand the machine’s maximum power output as indicated on the data plate (see Description of the tumble dryer). • The power supply voltage must fall within the values indicated on the data plate (see Description of the tumble dryer). • The socket must be compatible with the dryer’s plug. Should this not be the case, replace the plug or the socket. ! Do not use extension cords. ! The dryer must not be installed outdoors, even if the space is sheltered. It can be very dangerous if exposed to rain or storms. ! Once installed, the dryer’s electrical wire and plug must be within reach. ! The power cord must not be bent or squashed. ! The power cord is supplied fitted with a BS1363 plug and with a 13 amp BS1362 fuse. If it is necessary to fit a replacement fuse, it must be a 13 Amp ASTA approved to BS1362 type. WARNING: The plug must not be used without a fuse cover. If a replacement fuse holder/cover is required, it must be of the same colour coding or wording as shown on the base of the plug. Replacements are available from authorised dealers. Changing the plug The wires in the power cord are coloured in accordance with the following. Green and Yellow (Earth) wire to terminal marked “E”, symbol x, or coloured green and yellow. Blue (Neutral) wire to terminal marked ”N” oi coloured black. 13A ASTA approved fuse to BS 1362. Brown (live) wire to teminal marked “L” or coloured red. ! If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO nOt leave it where it can be inserted into a socket and create a shock hazard. ! The power cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorized technicians (see Service). New or longer power cords are supplied at an extra charge by authorized dealers. ! The manufacturer denies any responsibility should any of these rules not be followed. ! If in doubt about any of the above consult a qualified electrician. Preliminary information Once the tumble dryer is installed, clean the inside of the drum before operating it and remove any dirt accumulated during transportation. 4 Description of the tumble dryer (Î) inDesiT Opening the door Press the Features handle (pull to open) Control panel indicator light Drying time selector knob This is used to set the drying time: turn the knob in a clockwise direction until the indicator is set to the desired drying time (see Drying settings). High Heat button _q It can be used to customise the selected programme in accordance with your own requirements. START button Press the button to begin drying. Empty water container indicator light The "Empty water container” indicator light ^ signals that the water container must be emptied. If the container becomes full during the programme, the tumble dryer will automatically start the cold air cycle. In order to avoid this procedure, always empty the water container after using the tumble dryer (see Care and maintenance). 5 How to carry out a drying cycle Starting a drying programme 1. Plug the dryer into the power supply socket. 2. Select a suitable drying programme for the type of laundry (see Laundry). 3. Open the door, ensure that the filter is clean and securely placed and that the water container is empty and correctly slotted (see Care and maintenance). 4. Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door. 5. Turn the TIMER knob until the indicator is pointing towards the most suitable drying time for the type of fabric in that load. Use the table to check the relationship between fabric type and load capacity (see Drying settings), and make sure you are familiar with the instructions provided for...
Эта инструкция также подходит к моделям:Сушильные машины - IDC 75 S (547.45 kb)