Войти:
Скачали: 14   Размер: 2 mb   Производитель: Woodstock  
Категория: Рубанки
@name

Lift the cover off and set it aside. 4. Vacuum all dust and debris from the motor and belt areas. 5. Inspect the cutterhead belt for proper tension, straight alignment, and possible damage or wear. Note: The belt is properly tensioned if it deflects about -W when you press down on middle of the belt with moderate pressure from your thumb or forefinger. The belt is properly aligned if it lies flat and straight on the motor shaft and drive pulley. Belt damage will be evident on inspection. 6.

Скачали: 15   Размер: 6 mb   Производитель: Woodstock  
Категория: Рубанки
@name

1,510 Black Walnut............ 1,410 Red Alder................1,370 Basswood................1,280 Cottonwood............. 1,160 Western Larch...........1,150 Tamarack.................1,130 Douglas Fir..............1,080 Alaska Cedar............1,050 Sitka Spruce.............1,000 Sugar Pine.................980 Cypress.....................940 Redwood (OG)............930 Red Cedar ................. 860 T White Pine.................850 SOFT Balsam Fir................. 710 Figure 32.

Скачали: 34   Размер: 3 mb   Производитель: Woodstock  
Категория: Рубанки
@name

Скачали: 18   Размер: 3 mb   Производитель: Woodstock  
Категория: Рубанки
@name

9. Remove the wood that is holding the blade Top Dead Center Figure 25. Blade is positioned at its highestposition (Top Dead Center). Figure 26. Checking the blade height. Figure 27. Blade clamp screws. ADJUSTMENTS guard open. -19 Depth Of Cut The depth of cut is equal to the distance between the infeed table surface and the top of the cutterhead blade at top-dead-center (Figure 28). The depth of cut is adjusted by raising and lowering the infeed table. To adjust the depth of cut: • Turn the tab

Скачали: 10   Размер: 2 mb   Производитель: Woodstock  
Категория: Рубанки
@name

Скачали: 9   Размер: 660 kb   Производитель: Woodstock  
Категория: Рубанки
@name

shall not be responsible for damage or injuries caused by improper use or modification of this machine. • If you do not understand these instructions or if you have questions, contact Woodstock International Technical Support at (360) 734-3482 before proceeding. Model D3393 Elliptical Jig Instruction Sheet • Read and understand these instructions! Woodstock International Inc. shall not be responsible for damage or injuries caused by improper use or modification of this machine. • If you do not u

Скачали: 26   Размер: 5 mb   Производитель: Woodstock  
Категория: Рубанки
@name

5. Avoid dangerous environments. Do not operate this machine in wet or open flame environments. Airborne dust particles could cause an explosion and severe fire hazard. 6. Ensure all guards are securely in place and in working condition. 7. Make sure switch is in the “OFF” position before connecting power to machine. 8. Keep work area clean and free of clutter, grease, etc. 9. Keep children and visitors away. All visitors should be kept a safe distance away while operating unit. 10. Childproof w

Скачали: 24   Размер: 3 mb   Производитель: Woodstock  
Категория: Рубанки
@name

5. As your leading hand gets within 4" of the cutterhead, lift the push block up and over the cutterhead and place it on the work- piece as it passes over the outfeed table. Do the same thing when your trailing hand nears the cutterhead and try to maintain pressure on the outfeed table. Never let your hands get closer than 4" from the cutterhead! 6. Repeat steps 4-5 until the surface is flat. OPERATIONS -23 OPERATIONS -24- Edge Jointing Edge jointing is passing the workpiece over the jointer on

Скачали: 3   Размер: 2 mb   Производитель: Woodstock  
Категория: Рубанки
@name

Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for safer shipping. Jointer Inventory: (Figures 4-5) Qty A. Jointer Bed Assembly.....................................1 B. Fence........................................................1 C. Dust Collection Bag.......................................1 D. Push Blocks........

Скачали: 1   Размер: 10 mb   Производитель: Woodstock  
Категория: Рубанки
@name

Besides the data sheet and parts in this insert, the content in the Model W1754 owner's manual is the same for both machines. Before operating your new machine, you MUST read and understand this insert and the entire Model W1754 manual to reduce the risk of injury from improper use or setup. If you have any further questions about this manual insert or the differences between the Model W1754S and the Model W1754, contact our Technical Support at (360) 734-3482 or email tech-support@shopfox.biz.





Категории