Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for safer shipping. Jointer Inventory: (Figures 4-5) Qty A. Jointer Bed Assembly.....................................1 B. Fence........................................................1 C. Dust Collection Bag.......................................1 D. Push Blocks.................................................2 E. Fence Tilting Handle......................................1 F. Fence Bracket Assembly..................................1 G. Fence Sliding Handle......................................1 H. Locking Plate Assembly...................................1 I. Fence Support..............................................1 J. Dust Chute..................................................1 K. Dust Collection Bag Clamp...............................1 Hardware and Tools (Not shown) —Cap Screws M8-1.25 x 20...............................6 —Lock Washers 8mm......................................6 —Hex Wrench 4mm........................................1 —Hex Wrench 6mm........................................1 Awarning Keep machine disconnected from power until instructed otherwise. Figure 4. Large components. Figure 5. Small components. -11- B SETUP SETUP Model W1829 (Mfg. Since 9/11) Machine Placement Workbench Load: Refer to the Machine Specifications, on Page 3, for the weight and footprint specifications of your machine. Some workbenches may require additional reinforcement to support both the weight of the machine and materials. Working Clearances: Consider the size of material to be processed through the machine, space for auxiliary stands, work tables and other machinery when establishing a location for your Jointer. See Figure 6 for the overall machine measurements. Figure 6. Machine dimensions. Awarning USE helpers or power lifting equipment to lift this 6" Jointer. Otherwise, serious personal injury may occur. ACAUTION MAKE your shop "child safe.” Close and lock all entrances when you are away. NEVER allow untrained visitors in your shop when assembling, adjusting or operating equipment. Cleaning Machine The tables and other unpainted parts of your jointer are coated with a waxy grease that protects them from corrosion during shipment. Clean this grease off with a solvent cleaner or citrus-based degreaser. DO NOT use chlorine-based solvents such as brake parts cleaner or acetone—if you happen to splash some onto a painted surface, you will ruin the finish. Awarning NEVER clean with gasoline or other petroleum-based solvents. Most have low flash points, which make them extremely flammable. A risk of explosion and burning m exists if these products are used. Serious personal injury may occur if this warning is ignored! ACAUTION ALWAYS work in well-ventilated areas far from possible ignition sources when using solvents to clean machinery. Many solvents are toxic when inhaled or ingested. Use care when disposing of waste rags and towels to be sure they DO NOT create fire or environmental hazards. -12- Model W1829 (Mfg. Since 9/11) SHOP FOX, Bench Mounting The strongest bench mounting option is a "Through Mount" where holes are drilled all the way through the workbench, and hex bolts, washers, and hex nuts are used to secure the machine to the workbench. Another option for mounting is a "Direct Mount" where the machine is simply secured to the workbench with a lag screw. NOTICE This machine must be securely fastened to a stable working surface before operating. Failure to do so will produce unsafe operating conditions. Figure 8. Example of a direct mount. -13- SETUP SETUP SHOP FOX' Model W1829 (Mfg. Since 9/11) Assembly To assemble the jointer, do these steps: 1. DISCONNECT JOINTER FROM POWER! 2. Use two of the included M8-1.25 x 20 cap screws and lock washers 8mm to attach the fence support to the jointer bed, as shown in Figure 9. 3. Insert the locking plate assembly into the fence support, positioning it so the two pins are against the bottom edge of the fence support, as shown in Figure 10. Fence Support Figure 9. Attaching the fence support. Figure 10. Inserting the locking plate. 4. Secure the locking plate in position with the fence sliding handle, as shown in Figure 11. Locking Plate Assembly 5. Use the remaining four M8-1.25 x 20 cap screws and 8mm lock washers to attach the fence to the fence bracket assembly, as shown in Figure 12. Figure 11. Installing fence sliding handle. Figure 12. Attaching the fence bracket assembly to the fence. -14- Model W1829 (Mfg. Since 9/11) SHOP FOX, 6. Slide the fence bracket assembly over and onto the dovetail of the support and locking plate, as shown in Figure 13. Fence Bracket Assembly — - Æ Fence Support | Dovetail Figure 13. Sliding the fence bracket onto the fence...