Войти:
Скачали: 2   Размер: 2 mb   Производитель: Harbor Freight Tools  
Категория: Рубанки
@name

3. Remove the panels on both sides of the planer, and apply a light grease to the chains. Note: Do not apply grease to the belts. 4. Apply a light coat of grease to the chain on the underside of the machine. The motor and electrical controls should be maintained. 1. Keep the motor and electrical controls dry and clean. Do not expose the electrical portions of the machine to water or wet conditions. 2. Keep the motor free of chips, sawdust, grease, and debris. 3. The motor bearings are sealed and

Скачали: 8   Размер: 1 mb   Производитель: Harbor Freight Tools  
Категория: Рубанки
@name

Adjust the other Knife Adjustment Set Screw until the Knife just touches the straightedge on that side also. Turn the three Knife Holder Bolts firmly in the direction shown to the upper left to 11. secure the knife holder in place. Rotate the Drum 180° and change and adjust the other knife at the same time ac12. cording to the steps above. IMPORTANT!13. Carefully double check that the Knives and Knife Holders are secure and that the Knives are level before use. Note: If a knife is adjusted to cu

Скачали: 1   Размер: 1 mb   Производитель: Harbor Freight Tools  
Категория: Рубанки
@name

Blades require no adjustment and automatically locks into place. 8. Using gloves, rotate the Cutterhead (53) so that the second Blade is accessible. 9. Repeat steps 2 through 8 on the second Blade. 10. Replace the Blade Guard (14) and secure with Bolts (16). Securely tighten Bolts. Blade Guard (14) Magnets (123) Gib (56) Blade (57) Magnets (123) Cutterhead (53) Gib (56) ADJUST ROLLER CASE LEVEL. If the Roller Case (47) is not parallel to the base (104), the planer will produce cuts of uneven dep

Скачали: 3   Размер: 599 kb   Производитель: Harbor Freight Tools  
Категория: Рубанки
@name

4. There must not be objects, such as utility lines, nearby that will present a hazard while working. general Operating instructions dEPth KnOB (48) FrOnt BaSE rEar BaSE PlatE (54) PlatE (61) 1. While standing to the side of the wood stock, hold the Planer firmly with one hand on the handle portion of the Housing (15, 45), and the other hand on the Depth Knob (48). 2. Set the Front Base Plate (54) of the Planer on the front edge of the wood stock. Then, depress the Safety Lock Button (17) and sq

Скачали: 1   Размер: 146 kb   Производитель: Harbor Freight Tools  
Категория: Рубанки
@name

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mis

Скачали: 1   Размер: 863 kb   Производитель: Harbor Freight Tools  
Категория: Рубанки
@name

Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) Specifications Motor Speed 20,000 RPM Cutter Head Speed 10,000 RPM Input 120 V~ / 60 Hz / 4.5 A (no load) Cutting Knives 2 Maximum Planing Width 3.937” Maximum Cutting Depth .078” Fence Tilt 90-135 degrees Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or bro

Скачали: 2   Размер: 285 kb   Производитель: Harbor Freight Tools  
Категория: Рубанки
@name

Remove the center screw of the outlet cover and put the screw through the ring connector and back into the hole of the outlet cover. Do not over tighten or you will crack the outlet cover. VOLTAGE WARNING Common household current is 110-120 volts. As long as your tool is rated from 110V-120V there will be no complications using this tool with household receptacles. If your tool is rated 220V-240V it has a completely different style of plug and must be used with a 220V-240V receptacle. Never try





Категории