3. Lower/raise the bed rollers (Page 26). 4. Adjust knives to the proper height (Page 36). 5. Replace cutterhead bearings. Glossy surface. 1. Knives are dull. 2. Feed rate too slow. 3. Depth of cut too shallow. 1. Sharpen/replace knives (Page 36). 2. Increase feed rate (Page 25). 3. Increase depth of cut (Page 26). Inconsistent chip marks. 1. Chips are not being properly expelled from around the cutterhead. 1. Use an adequate dust collection system; adjust the chip deflector in or out, dependi

(For models manufactured since 5/10) #BL12964 printed in China Congratulations on your purchase of a Model G0453PX Planer! The Model G0453PX is the same machine as the Model G0453Z but with a "cool" new look. All parts differences are shown below. Except for the differences noted in this insert, all other content in the Model G0453Z manual applies to this machine. Before operating your new machine, you MUST read and understand this insert, and the entire G0453Z manual to reduce the risk of serio

Headstock Breakdown 4 3 G0453Z 15" Planer w/Spiral Cutterhead Headstock Parts List REF PART # DESCRIPTION 1 P0453Z001 HANDLE 2 PN09M HEX NUT M12-1.75 3 PW06M FLAT WASHER 12MM 4 P0453Z004 HANDWHEEL LABEL 5 P0453Z005 HANDWHEEL 6 P0453Z006 COLLAR 7 PR29M INT RETAINING RING 32MM 8 P6201 BALL BEARING 6201ZZ 9 PK48M KEY 4 X 4 X 20 10 P0453Z010 WORM GEAR 11 P0453Z011 WORM HOUSING 12 PSB137M CAP SCREW M5-.8 X 55 13 P0453Z013 ROLLER 14 P0453Z014 ROLLER STAND 15 PSB20M CAP SCREW M5-.8

Roller spring tension adjustment cap screws. G0453/G0454 (Mfg. Since 3/08) Figure 49. Chip deflector and securing hex bolts. * -43- 4. If the distance measured in Step 3 is not equal to W, then loosen the four hex bolts that secure the chip deflector and adjust the gap to W. 5. Re-tighten the hex bolts, then replace the belt cover, top cover, and dust hood. Scale Calibration Although correctly set at the factory, the scale can be adjusted for accuracy if it becomes necessary. Tools Need

Headstock Breakdown 3 G0454Z 20" Planer w/Spiral Cutterhead Headstock Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0453Z001 HANDLE 2 PN09M HEX NUT M12-1.75 3 PW06M FLAT WASHER 12MM 5 P0453Z005 HANDWHEEL 6 P0453Z006 HANDWHEEL COLLAR 7 PR29M INT RETAINING RING 32MM 8 P6201 BALL BEARING 6201ZZ 9 PK48M KEY 4 X 4 X 20 10 P0454Z010 WORM GEAR 11 P0454Z011 WORM HOUSING 12 PSB137M CAP SCREW M5-.8 X 55 13 P0454Z013 ROLLER 14 P0454Z014 ROLLER STAND 15 PSB01M CAP SCREW M6-1

#JK8066 PRINTED IN CHINA ...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Outlets should be located near each machine so power or extension cords are not obstructing high-traffic areas. Be sure to observe local electrical codes for proper installation of new lighting, outlets or circuits. Make your shop “child safe.” Ensure that your workplace is inaccessible to children by closing and locking all entrances when you are away. DO NOT allow unsupervised children or visitors in the shop at any time. -10-G0505 121.2" Lean & Mean Portable Planer Mounting to Bench Handle As

Factory adjustments that should be verified: 1. Outfeed Table Height (page 31) 2. Depth-of-Cut Scale (page 32) 3. Fence Stops (page 32) G0526 6" Jointer -21 SECTION 6: OPERATIONS General Your safety is important! Please follow the warnings below during this entire section: Damage to your eyes, lungs, and ears could result from failure to wear safety glasses, a dust mask, and hearing protec- tion while using this machine. Loose hair and clothing could get caught in machinery and cause serious per

Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator to reduce your risk. WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips which could cause a loss of workpiece control. HEARING PROTECTION. Always wear hearing protection when operating or observiing loud machinery. Extended exposure to this nois

Measure the lumber with calipers to determine its exact thickness. 2. Move the cutterhead to 1.16" under the thickness of your lumber and feed your test board through the planer. 3. Turn the handwheel one half rotation and run the board through once more. Turn the board over and repeat. Figure 30. Screw for column adjustment. -30- G0550/G0551 15" Planer Knife Inspection The Model G0550/G0551 Planer has a three- knife cutterhead. The cutterhead is located in the head casting and rotates on two se