Use good judgment! IMPORTANT: Whenever the blade guard cannot be used, the riving knife must be installed. Button Figure 68. Button for removing pawls. Riving Knife ▲WARNING To ensure that the riving knife works safely, it MUST be aligned with and correctly adjusted to the blade. Refer to Page 68 to check or adjust the riving knife alignment. The riving knife works in the same manner as the spreader on the blade guard assembly. It is a metal plate that prevents the newly cut workpiece fro

6/10+) MS -85- Cabinet -86- M G0605X1-6X1, G0696X-97X (Mfg. 6/10+) Cabinet Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 5 P0605X137 STRAIN RELIEF 7 PN02M HEX NUT M10-1.5 8 PW04M FLAT WASHER 10MM 9 PLW06M LOCK WASHER 10MM 16 PFB15M FLANGE BOLT M8-1.25 X 12 27 PLW04M LOCK WASHER 8MM 38 PK14M KEY 5 X 5 X 18 39 PB14M HEX BOLT M10-1.5 X 35 42 PCAP31M CAP SCREW M8-1.25 X 25 43 P0605X1043 WOODRUFF KEY 22 X 5 47 P0605X1047 HANDWHEEL 48 P0605X014 HANDWHEEL LOCK KNOB 49 PSS17

Build-up of material inside atomizing cap. 1. Clear holes. 2. Clean. 3. Clean. Heavy deposit of material in center. 1. The material flow exceeds the atomizing cap capacity. 2. Inlet air pressure is too low. 3. Material is too thick. 1. Lower fluid flow. 2. Increase inlet air pressure. 3. Thin material. Narrow center pat- tern. 1. Volume control turned in too far. 2. Inlet air pressure too high. 3. Fluid pressure is too low. 4. Material is too thin. 1. Increase volume. 2. Reduce inlet air pressur

C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com Web Site: Read the manual before operation. Become familiar with this tool, its safety instructions, and its operation before beginning any

1 F A E J I B C D G H K Figure 1. Model H8225 Inventory. Model H8225 21.2 Gallon Paint Tank with Gun -5 Tank Assembly Regulator Assembly Fluid Outlet Adapter Lift Handle Pressure Gauge Air Inlet Fitting Safety Valve Air Outlet Fitting Figure 2. Regulator and lift handle installed on paint tank. To assemble the paint tank: 6. Connect the material hose to the fluid outlet adapter on the tank lid. 1. Apply Teflon tape to all male pipe threads. 7. Install a pressure regulator (not includ- Figure " y

Stage two sprays material. 6. Cup: Holds material; includes a vented cap. -10- Model H8115/H8117 Spray Gun SECTION 4: OPERATIONS ADANGER 4 EXPLOSION HAZARD! DO NOT smoke or have any source of flame or spark near spraying. Vapors will explode if ignited. ▲WARNING RESPIRATORY HAZARD! Always use respirator rated for organic vapor and solvent use when using spray equipment. Failure to protect your lungs can lead to respiratory illness and nervous system damage. ▲WARNING TOXIC FUMES! Alway

parts. Non-slip footwear is recom-20. CHECK DAMAGED PARTS. mended. Wear a protective hair cov-Before further use of the tool, a ering to contain long hair. guard or other part that is dam 12. ALWAYS USE SAFETY GLASSES. aged should be carefully checked Also use a face or dust mask if cut-to determine that it will operate ting operation is dusty. Everyday properly and perform its intended eyeglasses only have impact resis-function. Check for alignment of tant lenses, they are NOT safety moving par

#PC8208 PRINTED IN TAIWAN SECTION 1: SAFETY Indicates a potentially hazardous situation which, if not avoided, MAYresult in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates a potentially hazardous situation which, if not avoided, COULDresult in death or serious injury. This symbol is used to alert the user to useful infor- mation about proper operation of the equipment. For Your Own Safety Read Instruction Manual Before Operating This EquipmentThe purpos