Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
1 F A E J I B C D G H K Figure 1. Model H8225 Inventory. Model H8225 21.2 Gallon Paint Tank with Gun -5 Tank Assembly Regulator Assembly Fluid Outlet Adapter Lift Handle Pressure Gauge Air Inlet Fitting Safety Valve Air Outlet Fitting Figure 2. Regulator and lift handle installed on paint tank. To assemble the paint tank: 6. Connect the material hose to the fluid outlet adapter on the tank lid. 1. Apply Teflon tape to all male pipe threads. 7. Install a pressure regulator (not includ- Figure " your -up, maintain on -your con- con- with gun. compressor the Figure 3. Paint tank connect to air compressor and spray gun. - Spray Gun Assembly Prior to assembly and use of the spray gun, thoroughly clean and dry all parts. Please Refer to Cleaning in the MAINTENANCE section on Page 13 for more detailed instructions. Make sure all connections are tight enough to prevent air leaks but not so tight as to damage the tool. Controls 1. Fluid Control: Controls the volume of material that travels through the fluid tip. 2. Pattern Control: Adjusts the spray pattern from a round pattern to a wide fan. 3. Air Flow Control: Controls the fluid pressure inside the spray gun. 4. Atomizing Cap: Controls the spray pattern from vertical to horizontal. 5. Trigger: Two stage trigger. Stage one only releases compressed air for blowing off the work piece. Stage two sprays material. Air Hose Material Hose Pattern ControlAtomizing Cap Trigger Fluid Control Figure 4. Material and air hoses attached to the spray gun. Model H8225 21.2 Gallon Paint Tank with Gun -7 OPERATIONS Tank Regulator The pressure regulator on the paint tank controls the amount of pressure in the paint tank and the spray gun. The following are operating guidelines for internal and external spray guns: Internal Mix Guns: Use higher tank pressures up to the full amount of air pressure being delivered to the spray gun. However, do not exceed 50 PSI at the spray gun or in the paint tank. External Mix Guns: Use lower tank pressures—approximately 12 PSI for most external mix guns. Start with the tank at "zero" pressure and increase pressure gradually until the correct spray pattern is achieved. Do not exceed the 50PSI maximum operating pressure on your paint tank. Exceedingthemaximumpressure maycausethetanktoexplode, causing serious personal injury. EXPLOSIONHAZARD!DONOTsmoke or have any source of flame or spark near spraying.Vapors will explode if ignited. RESPIRATORY HAZARD! Always useaNIOSH approved respirator when using spray equipment. Failure to protect your lungs can lead to respi- ratory illness and nervous system damage.Spraying some paints and varnishes may require a supplied air respirator system. TOXICFUMESan approved spray en- tilated area whVER spray in an coere toxic fumes anors can accumulate -8-Model H8225 21.2 Gallon Paint Tank with Gun Model H8225 21.2 Gallon Paint Tank with Gun -9- Read the manual before operation. Become familiar with this tool, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed. Like all tools there is potential danger when operating this tool. Accidents are frequently caused by lack of familiarity or failure to pay attention. If normal safety precautions are overlooked or ignored, serious personal injury may occur. To use your paint tank and spray gun: 1. Thoroughly mix and strain your paint to remove undissolved particles that could block the flow of material to the gun. 2. Pour paint into the tank; or set a one gallon can of paint in the tank, making sure the lid's fluid tube is seated in the can. 3. Place the lid assembly on the tank and evenly hand tighten the lid clamp wing screws. 4. Adjust the regulator at your air compressor to 50 PSI. 5. Fully turn the regulator T-handle counterclockwise to shut the tank regulator OFF. 6. Connect the paint tank to the air compressor. 7. Adjust the paint tank to 25 PSI on the tank pressure gauge. Normal operating pressure is 25-30 PSI. Using trial and error, adjust the paint tank as necessary between this range for optimum results. 8. Adjust the regulator at the spray gun. 9. Start by testing the spray gun at a low setting, then increase the air pressure as needed for satisfactory results. Tank Setup This paint tank is not designed for use with highly abrasive, corrosive, or rust inducing materials. If such materials are used, frequently and thoroughly clean all components to reduce the need to replace parts. ............ 7. Adjust the fluid control knob to start Spraying with a low volume of material and keep the atomization as low as possible. You will need to use a combination of The Model H8225 siphon feed spray gun set is designed to spray a wide variety of materials such as lacquers, stains, primers, multi-component paints, clear coats, acrylics, epoxies etc. It is ideal for auto body and woodworking projects. To use your spray gun: 1. Read and follow the material manufa...