Оценок - 3, средний балл: 3.7 ( )

Производитель: Campbell Hausfeld Размер: 7.95 mb Название файла: Язык инструкции:

NOTE: Strain and thin paint before using. All paint may have particles that will clog filter and spray tips. Remove any skin which may have developed on Operating Instructions and Assembly Instructions Airless Paint Sprayers the paint due to air exposure. Follow paint manufacturers’ recommendations on thinning paint. 12. When pure paint appears from spray tip rotate tip to the Spray position. The system is now ready for use. Clean Position 1 Spray Position 2 12” Holding Spray Gun Thin Coat Thin Coat Heavy Coat Overspray Overspray Result of Flexing Wrist While Spraying Approx. 10-12” Start Stroke Pull Trigger Release Trigger End Stroke Proper Way to Trigger Spray Gun Inco rrect Spraying Instructions Professional looking results can be obtained by following the spray tips below. 1. Keep the gun perpendicular to the surface. Always hold the gun perpendicular to the surface with the tip approximately 12 inches from the surface. If held at an angle (up and down or side to side), paint will build up unevenly, leave the work splotchy, and cause excessive overspray (See Figure to the right). 2. Move with a smooth arm stroke. Move the gun at a steady, even pace while keeping the gun perpendicular to the surface (See Figures to the right). Do not fan the gun. Fanning the gun will cause excessive overspray and uneven coverage (See Figure to the right). 3. Start moving the gun before triggering. To get a smooth overlap and prevent initial paint buildup, start your stroke movement before pulling the trigger. Release the trigger before stopping at the end of the stroke (See Figure to the right). NOTE: To assure uniform paint coverage, overlap each stroke by 20% - 30% and use two coats with a cross pattern (one coat horizontal, second coat vertical). Prevent clogged tip Water Airless Paint Sprayers Operating Instructions and Assembly Instructions Spraying Instructions (Continued) INTERM ITTENT USE If you are spraying and decide to stop for several minutes, lock the spray gun trigger and submerge the tip in a container of water (See Figure on page 8). This will prevent paint from hardening in the tiny spray opening and clogging the tip. Be sure to release the pressure in the system and turn the unit off. CLEARING CLOGS REVERSIBLE TIP: (Included ) 1. Rotate the tip to the clean position (See Figure 1 on page 8). 2. Point gun in a safe direction and spray. This should clear tip of any blockage. 3. Rotate the tip back to the spray position and continue spraying (See Figure 2 on page 8). 4. If clogging continues, replace gun filter and consider straining the paint prior to use. Equipment damage can occur if a needle or sharp object is used to clean the tip. Tungsten carbide is brittle and can be chipped. HOW TO CHANGE SPRAY TIPS It may be necessary to change spray tips during a paint job. Follow these steps for safe, easy tip changes. 1. Depressurize and turn off unit per manufacturer’s instructions. 2. Engage gun trigger lock. 3. Pull red tip insert out of spray base and replace with different tip, fully inserting tip into base. HOW TO ATTACH ROLL ER ACCESSORY 1. Depressurize and turn off unit per manufacturer’s instructions. 2. Engage gun trigger lock. 3. Remove spray base, tip, seal and washer assembly. 4. Attach roller accessory (AL2275 shown) to airless spray gun. If needed use thread adapter and washer between roller and spray gun as shown. Figure - Attach roller accessory to spray gun Cleanup cleanup fo r OVERNIGHT STORAGE NOTE: Cleaning and maintenance of the pump are the most important steps you can take to ensure proper operation and a long life for your airless paint sprayer. Please follow the cleaning instructions carefully and . . . WEAR ALL NECESSARY SAFETY GEAR Necessa ry Too ls / Mate ria ls: • One (1) bucket • Water • Plastic wrap When reusing the sprayer with the same paint the next day at the same job site, it is not necessary to flush the paint from the system. However, it is important t o keep air from coming into conta ct with the paint. NOTE: Do NOT disconnect any hoses. 1. Turn prime/spray control to PRIME position. High pressure hose may still be pressurized with prime/spray control in the PRIME position. With the gun pointed in a safe direction, pull the gun trigger to relieve any pressure in the hose. 2. Engage gun trigger lock. 3. Place spray gun in bucket of water. There should be enough water to cover spray tip. This will prevent paint from drying or clogging tip. 4. Leave suction and bypass tubes in bucket of paint. Make sure ends of suction and bypass tubes are below surface of paint in bucket. 5. Cover bucket and tubes with plastic wrap or a damp towel to prevent film forming on paint. Or, if using latex paint, pour a very thin layer of water over top of paint. Stir water into paint the next morning. Airless Paint Sprayers Operating Instructions and Assembly Instructions Turn Prime/Spray Control to PRIME Position 1 3 Place Gun in Water Latex Paint: Use Thin Layer...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: