Оценок - 3, средний балл: 5 ( )

Производитель: Campbell Hausfeld Размер: 7.95 mb Название файла: Язык инструкции:

Part No. Description No. Q ty. R ef. Part No. Description No. Q ty. 10 Suction Bell (with filter) AL111000AJ 1 11a Suction Tube Assembly AL138400SV 1 11b Option, Solvent Resistant AL138404SV 1 12 Bucket Support (with screws) AL168080SV 1 13 Wheel, Pneumatic (optional) WA005620AV 2 14 Cap, Rubber (optional) MJ110300AV 2 15 Bucket Support (w/screws & nuts) AL167953SV 1 16 Stand AL168020AD 1 15 16 14 13 12 11 10 9 8 7 6 5 4 3 2 1 8 1 2 3 4 5 6 Operating Instructions and Assembly Instructions Troubleshooting Chart Symptom Possible Cause(s) Corrective Action Motor hums and does not run 1. Unit under pressure 1. Turn Prime/Spray Control to prime position 2. Equipment has been dropped 2. Take to authorized service center to have motor assembly which caused motor to become realigned. Or, call technical support misaligned 3. Supply voltage too low 3. Do not use an extension cord, it is better to add hose length. Use portable generator with a 2400 VA minimum rating Motor does not run or hum 4. Power Switch is in OFF position 4. Flip Power Switch to ON position 5. Bad power connection 5. Check power connections at power receptacle, along extension cord and at equipment for looseness or damage 6. Circuit breaker or fuse is tripped 6. Correct cause of circuit overload. (Possible causes: Supply voltage too low, extension cord too long for available supply voltage, equipment was under pressure while trying to start motor or motor has been damaged.) 7. Thermal overload protection 7. Allow motor to cool for approximately 30 minutes, determine activated cause and restart motor. (Possible causes: Supply voltage too low, extension cord too long for available supply voltage, equipment was under pressure while trying to start motor or motor has been damaged.) Motor runs, but pump does 8. Check valves stuck 8. “Pop” Inlet Valve and Outlet Valves. See Preparation not prime after being cleaned Instructions after last use. (This problem 9. Suction Assembly loose and/or 9. Remove Suction Assembly, clean sealing surfaces and can usually be prevented by sealing surfaces are dirty at Inlet reassemble following the recommended Valve cleaning and storage procedure) 10.Suction Head not immersed in 10.Add more paint to bucket and/or adjust position of Suction paint Assembly 11.Prime/Spray Control is in the 11.Turn the Prime/Spray Control to the Prime position and Pressure spray position and/or the Control fully clockwise Pressure Control is in the Low Pressure/Hydraulic Bleeding position 12.Hydraulic system contains air 12.Turn Pressure Control to Low Pressure/Hydraulic Bleeding position for 1 minute while motor is running 13.Hydraulic oil level low 13.Add oil so level is within 1/4” of housing edge. (See notes in Maintenance Section on oil leaks.) Turn Pressure Control to Low Pressure/Hydraulic Bleeding position for 1 minute Motor runs, but pump does 14 See Possible Causes 9,10,11,13 14.See Corrective Actions 9,10,11,13 not prime even though it was working just fine a little while ago. (Usually occurs after 15.Clogged suction filter 15.Remove suction filter and clean. Also, refer to Maintenance section moving or adding more paint to the paint bucket.) 16.Trash caught in valves 17.Paint sediments settled to 16.See “Force Feeding” figure on page 23 17.Strain and mix paint thoroughly bottom of bucket Pump primes, but does not build pressure 18.Prime/Spray Control not in Spray position 18.Turn Prime/Spray Control to Spray position 19.Pressure Control not set to high enough pressure 19.Turn Pressure Control clockwise to desired pressure. Fully clockwise is maximum pressure 20.Even though Prime/Spray Control is in Spray position, fluid still flows from By-Pass Tube. Prime/Spray Control is worn or damaged 20.Replace with service kit (See replacement parts list) or take equipment to authorized service center Continued on next page 21 Operating Instructions and Assembly Instructions Troubleshooting Chart (Continued) Symptom Possible Cause(s) Corrective Action Pump primes and builds pressure, however, the equipment does not spray or produce a quality spray pattern 21.Clogged gun filter 21.Replace with new filter. Do not attempt to clean gun filters. Also, refer to Maintenance section 22 Clogged Spray Tip 22.See Clearing Clogs section 23 A. Tip is damaged or worn 23.A. Replace tip. Also, refer to Maintenance section B. Paint requires thinning B. Follow paint manufacturers thinning recommendations. Paint should not typically need to be thinned more than 8 oz. of solvent per gallon C. Reversible Spray Tip in cleaning position C. Turn Spray Tip to Spray position. See Cleaning section for details Pump primes and builds pressure, but does not maintain pressure once trigger is pulled 24.Clogged Suction Filter 24.Remove Suction Filter and clean. Also, refer to Maintenance section 25.Suction Assembly loose and/or sealing surfaces are dirty at Inlet Valve 25.Remove Suction Assembly, clean sealing surfaces and reassemble hand tight 26.Paint thi...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: