Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
2. Sleep button. 3. Minute button. 4. Hour button. 5. Time set button. 6. Snooze. TIMESLEEPALARM/ OFFMinuteHourSNOOZE6 Controls (front) 67 8 6. Alarm indicator. 7. PM indicator. 8. Tuning control. 8892MHz 540600kHz CR 9923 2BandClockRadioPMTUNINGFM MW If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Controls (left and right LowHighOnOffRadioBuzzDIMMER 9 10 9. Function switch. 10. Dimmer switch. 11. Waveband switch. 12. Volume control. 13. Battery compartment 11 12 MWFMVOLUME13 Switching 1. Place your clock on a flat surface. wall socket and switch The clock display will 8892MHz 540600kHz CR 9923 2BandClockRadioPMTUNINGFM MW ON TIME Setting the time 1. Press and hold down the TIME button. 2. Whilst holding down the TIME button press the Hour or Minute Minute Hour buttons to set the time. Release the buttons when the correct time is reached. The clock uses a 12 hour display with an PM indicator. Ensure that the correct 12 hour cycle is selected. PM If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Listening to On 1. Switch on the radio Function switch to the 'On' Off position. Radio Buzz 2. Select the required waveband using the Waveband selector switch. MWFM 3. Tune in to the desired station by rotating the Tuning control. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for 8892MHz 540600kHz TUNINGFM MW VOLUME On optimum reception. Off Radio For MW reception there is a built in ferrite aerial. Rotate the your Buzz clock radio to the position giving best reception. 4. Adjust the volume by rotating the Volume control. 5. The radio can be switched off by sliding the Function switch to the 'Off' position. Setting alarm ALARM/ OFF Minute Hour 1. Press and hold down ALARM/OFF button. 2. Whilst holding down the ALARM/OFF button press the Hour or Minute buttons to set the time. Release correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour selected. PM Checking the alarm time 1. To check alarm time, press and hold down the ALARM/OFF button the display will show the alarm time. ALARM/ OFFPM If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Setting the 1. Set the alarm time Set the Function switch to the 'Buzz' position. The Alarm indicator will light. On PM minutes. To switch off the alarm until the next day ALARM/ Radio OFF button. To turn off the alarm permanently set the Function Buzz switch to the 'Off' position. The alarm will sound every day 59 Off Setting the alarm to wake to radio 1. Set the alarm time as previously described. Set the Function switch to the 'Auto' position. The Alarm indicator will light. On Ensure that the volume is set to the correct level and the desired PM Off station is tuned in. Radio The alarm will sound every day at the preset time for 1 hour 59 Buzz minutes. To turn off the alarm until the next day press the ALARM/ OFF button. To turn off the alarm permanently set the Function switch to the 'Off' position. Snooze control 1. The radio or buzzer the SNOOZE button. This sequence can alarm is sounding. SNOOZE PM Sleep timer SLEEP The radio can be set to turn off after a preset time has elapsed. 1. Press and hold down the SLEEP button. 2. Whilst holding down the SLEEP button set the sleep time using the Hour and Minute buttons (maximum 1 hour and 59 minutes in 1 minute steps) . The radio will switch off after the sleep time has elapsed. 3. To cancel the sleep function before the preset time has expired, press the SNOOZE button. SNOOZE If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Dimmer Switch DIMMER allow you to adjust the clock display to High brightness. The DIMMER switch located on the side of your clock Low Specifications Circuit Features Power Requirements Loudspeaker 8 ohms Mains : AC 230 volts, 50Hz only Output power 250mW Back-up Battery : IEC size 6LR61 (6F22, PP3) Aerial System FM Wire Aerial Frequency Coverage FM 87.5 - 108MHz MW Built-in Ferrite aerial MW 525 - 1610kHz ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH SOUTH YORKSHIRE S64 8YT The Company reserves the right to amend the specification without notice. General Do not allow this It is recommended that the FM band in terms of quality and freedom than on the MW band. Mains supply The CR9923 will operate from a AC 230volts, 50Hz only. For your convenience this product is supplied with a plug with a fuse of the appropriate rating. If for your socket outlet, it should be removed the terminal screws and removing the cable. The correct style of plug to suit your household rated fuse should be fitted. IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN IMPORTANT. DO NOT make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured Green or Green-and-yellow...