Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Ensure no overfilling when adding fabric conditioner in compartment 3. The washer-dryer automatically adds the softener to the wash in each programme. Liquid detergent is poured into compartment 2 just a few seconds before starting the wash cycle. Remember that liquid detergent is only designed for wash cycles of up to 60 degrees on non pre-wash items. Special containers are sold with liquid or powder detergents for placing inside the washer-dryer drum, these are positioned according to the instructions found in the detergent box Never use hand wash detergent, because it may form too much foam, which could damage the washer-dryer. Detergents that are specifically formulated for both hand and machine wash are an exception. One last secret: when washing with cold water, always reduce the amount of detergent you use: it dissolves less easily in cold water than in hot water, so part of it would be wasted. 1 2 3 In compartment 1: Detergent for pre-washing (powder) In compartment 2: Detergent for washing (powder or liquid) In compartment 3: Additives (softeners, perfumes, etc.) The detergent dispenser can be removed and cleaned: pull it outwards, as indicated in the figure. Then leave it under running water for a few minutes. Cutting costs efficiently A guide to environmentally friendly and economic use of your appliance. MAXIMISE THE LOAD SIZE Achieve the best use of energy, water, detergent and time by using the recommended maximum load size. SAVE up to 50% energy by washing a full load instead of 2 half loads. DO YOU NEED TO PRE-WASH? For heavily soiled laundry only! SAVE detergent, time, water and between 5 to 15% energy consumption by NOT selecting Prewash for slight to normally soiled laundry. IS A HOT WASH REQUIRED? Pretreat stains with stain remover or soak dried in stains in water before washing to reduce the necessity of a hot wash programme. SAVE up to 50% energy by using a 60°C wash programme. BEFORE USING A DRYING PROGRAMME ... SAVE energy and time by selecting the highest suitable spin speed to reduce the water content in laundry before using a drying programme. Instructions for installation and us. 8 Troubleshooting Before calling, read the following In most cases, when your washer-dryer fails to work, the problems arising can be easily solved without having to call for a technician. Before calling for assistance, always check these points. The washer-dryer fails to start. Is the plug correctly inserted into the socket? It could have been moved whilst cleaning. Is there electricity in the house? A circuit breaker may have switched off as a result of too many electrical appliances working at the same time. Or maybe due to a general failure in your entire area. Is the washer-dryer door closed properly? For safety reasons, the washer-dryer cannot work if Turn off the water supply after use. This will eliminate the possibility ofleakage. Always leave theappliance door ajarto avoid bad odours. Clean the appliance’sexteriors gently. To clean the exteriors and the rubber parts of theappliance, alwaysuse a soft cloth dipped in warm and soapy water. the door is open or not shut properly. Is the On/Off button pressed? If it is, then a programmed start has been set. Is the programmed start knob, in the correct position for those models concerned? Is the water supply turned on? For safety reasons, if the washer-dryer does not load water, it cannot start a wash cycle. Leave the washer-dryer plugged in while cleaning. Even during maintenance, the appliance should always be unplugged. Use solvents and aggressive abrasives. Never use solvents or abrasives to clean the external and rubber parts of the washer-dryer. Neglect the detergent dispenser. It is removable and can easily be cleaned by leaving it under running water. Go on holiday without thinking about her. Before leaving, always make sure that the washer-dryer is unplugged and that the water supply is turned off. Simple: with the new Indesit technology, you need less thanhalf of it, to get good results on twice as much! This is why you cannot see the water through the door: because there is little, very little of it, to respect theenvironment yet without renouncing maximum cleanliness. And, on top of that, you are also saving electricity. But where did all the water go? off, select one of the symbols stop/reset , then switch it back on. If the knob continues to turn, call for assistance because it is showing an anomaly. The washer-dryer fails to fill with water. Is the hose correctly connected to the tap? Is there a water shortage ? There could be work in progress in your building or street. Is there sufficient water pressure? The autoclave may be malfunctioning. Is the tap filter clean? If the water is very calcareous, or if work has recently been carried out on the water piping, the tap filter could be clogged with particles and debris. Is the rubber hose kinked? The tract of the rubber hose bringing water to washer- dryer must be as straight as possible....